Catalog excerpts
Congrav® CB-E 3.0 Feeder Controller General Information The Congrav® CB-E 3.0 is the latest generation of DIN rail mounted controller for all Brabender Technologie loss-in-weight or weigh belt gravimetric feeders. This module is typically mounted in a control cabinet. Each Brabender Congrav® CB-E 3.0 module has multiple advanced RISC processors that perform the calculations necessary to provide accurate feeder performance and is designed for demanding industrial environments. The control module Congrav® CB-E 3.0 is interconnected by a bus and connected to either the Congrav® OP1-S (for a single feeder) Congrav® OP6-E (up to 6 feeders) or the Congrav® OP16-E (up to 16 feeders) The controllers can also communicate directly with most host/SPS systems, whether as a single component or multi-component controller. The unit conforms to CE directives and is characterized by high electromagnetic compatibility. Inputs and outputs Inputs 6 digital inputs* (24 VDC) often used for start/stop or interlock 1 digital input can be used as frequency input for digital speed measurement. 6 digital outputs* (24 VDC) often used for run, refill and alarms *1 input/output is occupied internally – only 5 inputs/outputs are available for customer use Interfaces The control module Congrav® CB-E offers several interfaces including: Interface Interface for IDL-F, MD, DLS load cell To read the load cell weight signal and DMS digital Module (RS 422) Host-/SPS-interface Communicate to host systems. Available protocols: Ethernet Modbus TCP, Profibus DP, Profinet, EtherNet/IP For communication to Congrav® OP6-E and OP16-E operator interface or PC for operation, diagnostics and maintenance To regulate motor speed Digital and analog expansion modules (RS 485) For communication to Congrav® OP1-S single feeder operator interface for operation, diagnostics and maintenance Brabender Technologie GmbH & Co. KG, Kulturstr. 49, 47055 Duisburg, Tel.: +49(0)203 9984-0, email@brabender-technologie.com 9 Changes reserved Stan
Open the catalog to page 1Congrav® CB-E 3.0 Feeder Controller Optional expansion The hardware of the Congrav® CB-E 3.0 can be extended by optional expansion modules. These modules are connected to the serial interface and are supplied with 24VDC power from the Congrav® CB-E 3.0. Digital I/O module: 4 digital inputs (e.g. start, stop, clear fault, etc.) and 4 digital outputs (e.g. operation, fault, etc.) Analog I/O module: 2 analog inputs 0(2)-10 V (e. g. analog guidance), 2 analog outputs 0(4)-20 mA (e. g. process value, manipulated variable) Technical Specification Technical Specification Rated voltage Ripple,...
Open the catalog to page 2All Kubota Brabender Technologie GmbH catalogs and technical brochures
-
Work Standard - CDW
2 Pages
-
Work Standard - DDSR60
2 Pages
-
Work Standard - DS80
2 Pages
-
Work Standard - DS28
2 Pages
-
FlexWall®Plus FW80/1
2 Pages
-
Work Standard - FX
2 Pages
-
Work Standard - MiniTwin 2.0
2 Pages
-
Work standard - DSR103
2 Pages
-
Work Standard - DS60
2 Pages
-
Work Standard - FlexWall®
2 Pages
-
Work Standard - JetFilter
2 Pages
-
Work Standard - RotoTube
2 Pages
-
Work Standard - FDDW
2 Pages
-
Work Standard - BagDumper
2 Pages
-
DiB Plastics EN
30 Pages
-
DiB Food
28 Pages
-
Work Standard - Congrav CM-E
2 Pages
-
Work standard - Congrav CB-S
2 Pages
-
Work Standard - SiloTray
2 Pages
-
Work Standard - DBW
2 Pages
-
Work Standard -BagMaster
2 Pages
-
Work Standard - BAV
2 Pages
-
Work Standard- DVT
2 Pages
-
FEEDING LIQUIDS
2 Pages
-
Discharging and Refilling
2 Pages
-
PLASTICS BULK MATERIAL SOLUTIONS
30 Pages
-
DDW-M-DS80-100-200-E
2 Pages
-
DDW-M-DS60-E
2 Pages
-
BULK INGREDIENT SOLUTIONS FOOD
17 Pages
-
THE VERSATILE FLEXWALL®PLUS
2 Pages
-
Granule screw DDW-M-DS28
2 Pages
-
SERVICE OVERVIEW BROCHURE
12 Pages
-
PHARMA OVERVIEW BROCHURE
16 Pages
-
PLASTICS OVERVIEW BROCHURE
16 Pages
-
PRODUCTS OVERVIEW BROCHURE
20 Pages