MoBo Actuator
8Pages

{{requestButtons}}

Catalog excerpts

MoBo  Actuator - 1

TU6-0093 SSf|3*ffl|x£pi-22-U 1-22-U Yaguchi, Ohta-ku, Tokyo U6-0093, Japan Ultra compact Actuators with Direct Motor Drive Ball Screws.

Open the catalog to page 1
MoBo  Actuator - 2

MOBOT^^ILI-* (MA^'J-X) MoBo Actuator (MA Series) Direct Motor Drive Ball Screws are built in this series, what we call MoBo Actuators. All of MoBo Actuators are produced as customized products, in accordance with customer's order. More compact design of Unit products in longitudinal dimension became reality by using Direct Motor Drive Ball Screws / Resin Lead MoBo Actuator series is classified into MoBo Cylinder and MoBo Slider, which is Rod type and Table type respectively. There are several kinds of MoBo Cylinder/ MoBo Slider shown below. Each Cylinder / Slider has a different kinds of...

Open the catalog to page 2
MoBo  Actuator - 3

•ttti Specifications MoBoT7^7?1^.!—^ (MoBov'J /MoBo77^ Overall specifications for MoBo Actuators (MoBo 0$Jffl§ttil—K^i-XTt^LSfo Cylinder & MoBo Slider) are shown in Table below. Piffles \t";SiSt^lit!4 LTt^ST^Ts o#,B,?X7cc?L^o For further information, please see dimension Table. • Motor : 5-phase Stepping Motor LJ24 , 0.75A/phase • Photo Micro sensor: EE-SX1103(0mron) , DC5V50mA (Motor side and Travel end)

Open the catalog to page 3
MoBo  Actuator - 4

MoBoActuator MoBoT^^-il— MoBo Cylinder Cylinder type [Connection Diagram /IPHH] 5-phase Stepping Motor lead wire(AWG26J _Black / it—iG^ND Photo micro sensor lead wire(AWG30J [zi#.^$iMtRE/ Connector choice] Please designate connector type below. No connector if there is no designation. (AMP : 1 7221 1 -6 pins for Motor + 1 7221 1 -4 pins for Sensor) Upper side (white dot) [El-Connector / Elzi^Sttl Note 1) Model Number above is for no-connector and lead wire is set on riqht side on Motor. Note 2) Acceleration & Deceleration Rate above is our recommendation. Note 3) Dimension above is our...

Open the catalog to page 4
MoBo  Actuator - 5

MoBoActuator MoBoT^^-il— MoBo Slider Slider type N-03-05 depth 3 spot facinc [Connection Diagram /IPHH] Red;£ll 1 5-phase Stepping Motor lead wire(AWG26; _Black /M—JG^ND Photo micro sensor lead wire (AWG30J [zi#.^$iMtRE/ Connector choice] Please designate connector type below. No connector if there is no designation. (AMP : 1 7221 1 -6 pins for Motor + 1 7221 1 -4 pins for Sensor) Upper side (white dot) [El-Connector / EO*?$tt£ Note 1) Model Number above is for no-connector and lead wire is set on right side on Motor. Note 2) Acceleration & Deceleration Rate above is our recommendation....

Open the catalog to page 5
MoBo  Actuator - 6

KSS provides Standard Stepping Motor Driver, Extension Cable, and Photo Sensor Amplifier Board for Mo Bo Cylinder / Mo Bo Slider in order to make it [tl^ K7*f /t / Stepping Motor Driver] This Driver is for 5-phase Stepping Motor operated by DC24V power supply. It has automatic current reduction circuits. You can choose full-step or half step Micro-Step Driver for 5-phase Stepping Motor with DC24V power supply. 16 step angle types can be set with up to 250 divisions. This type can be operated with AC100V power supply. It has also Micro Step function [7* h-b>-tr77>7St5/ Photo Sensor Amplifier...

Open the catalog to page 6
MoBo  Actuator - 7

KSS MoBov'J>^-s MoBoT^^-s ^Wr-Zf Wire connections between MoBo Cylinder/ Slider, Extension cable and KSS standard Driver (KR-A5CC, Sensor power supply, Photo Sensor Amplifier Board is needed. Wire connection for this case is shown MoBo Actuator Please use them if necessary. J. _; - esse of Lighting on/sHM"^) Photo sensor Amplifier Board (SP4461) (Option) This Amplifier Board is necessary under 24V of Sensor power supply Wire connection for 5-phase Stepping Motor Driver (KR-A5CC) including Photo Sensor Amplifier Board MoBo Actuator Please use them if necessary. J. LS n case of lighting...

Open the catalog to page 7
MoBo  Actuator - 8

•Precaution of handling and operating 1) Before using these products, please read instruction manuals and follow the precautions below. 2) Do not hit or drop the Shaft, do not apply Axial or Radial load exceeding specifications, 3) Before using, please check that the product has no defect, and product is the same as your order. A) Do not disassemble each component, dust may get inside the product. It may deteriorate accuracy. 5) Please prevent contamination from dust or swarf. Dust or swarf may cause damage to Ball Screw/Lead Screw, which lead to deteriorating the function. 6) MoBo...

Open the catalog to page 8

All KSS catalogs and technical brochures