Miniature Actuators Flex Actuator
20Pages

=PU6-0093 m«f|3*ffl|x£P1-22-U 1-22-U Yaguchi, Ohta-ku, Tokyo U6-0093, Japan

Flex Actuator Series Many variation of KSS Flex Actuator became reality. Various choices among accuracy (Lead Screw type), speed (Screw Lead), Travel length and power(Motor >^KTfc U s fllJAt ^ U MJt#WX Z £ T o • We make full use of features of Miniature Ball Screw manufacturer and super compact design Actuator can • Depending on kinds of Lead Screws, wide range of choices related to positioning accuracy are available. • Several variations of Screw Lead & Travel for each Screw type are standardized. So wide variety of choice • Motor-less type is our standard, but a couple of Motors are in...

•nftflf/ Model number notation FA : KSS Flex Actuator Series ©Actuator type ©Lead Screw / Ball Screw type Re : Resin Lead Screw R : Rolled Ball Screw G : Precision Ball Screw ©Lead / Pitch (mm) : 020 means 2mm ©Motor type None : No Motor (Standard) M : Minebea Motor 2-phase Stepping Motor T : TAMAGAWA SEIKI 2-phase Stepping Motor $ E : Oriental Motor 5-phase Stepping Motor ©Connector type ©Direction of Motor leads R : Right (from Shaft end side) None : no optional design S : Photo micro Sensor outside B : Solenoid Brake Unit U : Side Motor mounting kit •Combination & Specifications mtfott u...

•Selection guide KSS Flex Actuator has a lot of combinations with Drive screws, Screw Lead, Travel length and Motor as an Therefore, when you try to select the suitable combination, its procedure may be complicated. KSS shows the selection guide below from the various a 1) ^ - ^ x ©s^r s e u s uffia;*fe«js s p y; K ^ - v a > it s ft§iijs s p«» im mm t & u s t= >±2) i¥«co t AT a.^mm^m <IEZI\ Note 1) In case of Standard (Motor-less), Repeatability & Lost motion are reference value, Permissible speed & Load Capacity are recommended value Note 2) For more detail, please refer to dimension table

Motor-less type (Standard) Resin Lead Screw type Actuator fah^4.5mmJ^F*] (Screw length : less than 4.5mmJ JScrew length : less than 6mmJ ^ Origin LS lead wire(Bare) DAcceleration & deceleration rate is our recommendation 2)There should be no condensation when using 3) Permissible Moment is the number when no load in other direction 4) Please consider Torgue as reference number 5) In case of Motor-less type, Repeatability & Lost motion are reference number 5) In case of Motor-less type, Permissible speed & Load Capacity are -ecommended number 7) Reguired Torgue is under maximum vertical Load...

Motor-less type (Standard) Rolled Ball Screw type Actuator fah^4.5mmJ^F*] (Screw length : less than 4.5mmJ JScrew length : less than 6mmJ \ Origin LS lead wire(Bare) DAcceleration & deceleration rate is our recommendation 2)There should be no condensation when using 3) Permissible Moment is the number when no load in other direction 4) Please consider Torgue as reference number 5) In case of Motor-less type, Repeatability & Lost motion are reference number 5) In case of Motor-less type, Permissible speed & Load Capacity are -ecommended number 7) Reguired Torgue is under maximum vertical...

Motor-less type (Standard) Precision Ball Screw type Actuator fah^4.5mmJ^F*] (Screw length : less than 4.5mmJ JScrew length : less than 6mmJ \ Origin LS lead wire(Bare) DAcceleration & deceleration rate is our recommendation 2)There should be no condensation when using 3) Permissible Moment is the number when no load in other direction 4) Please consider Torgue as reference number 5) In case of Motor-less type, Repeatability & Lost motion are reference number 5) In case of Motor-less type, Permissible speed & Load Capacity are -ecommended number 7) Reguired Torgue is under maximum vertical...

Resin Lead Screw type Actuator faU>^4.5mmJ^F*] (Screw length : less than 4.5mmJ

Rolled Ball Screw type Actuator faU>^4.5mmJ^F*] (Screw length : less than 4.5mmJ

Precision Ball Screw type Actuator faU>^4.5mmJ^F*] (Screw length : less than 4.5mmJ

2-phase Stepping Motono.95A/ phase & D28) with Resin Lead Screw type Actuator ffoVMl.bmmiilfti (Screw length : less than 4.5mm)

2-phase Stepping Motono.95A/ phase & D28) with Rolled Ball Screw type Actuator /fclJS4.5mmJ^|^ (Screw length : less than 4.5mmJ

2-phase Stepping Motono.95A/ phase & D28) with Precision Ball Screw type Actuator /fclJS4.5mmJ^|^ (Screw length : less than 4.5mmJ

5-phase Stepping Motono.75A/ phase & D28) with Resin Lead Screw type Actuator /fcUS4.5mmJ^|^ (Screw length : less than 4.5mmJ

5-phase Stepping Motono.75A/ phase & D28) with Rolled Ball Screw type Actuator /fcUS4.5mmJ^|^ (Screw length : less than 4.5mm)

5-phase Stepping Motono.75A/ phase & D28) with Precision Ball Screw type Actuator /fcUS4.5mmJ^|^ (Screw length : less than 4.5mmJ

[WM~7l'—*r3-—y b / Solenoid Brake Unit] If Flex Actuators are operated in vertical position, Ball Screw / Lead Screw may fall down when its power is off. Solenoid Brake Unit is effective to maintain intermediate position. [^E—£f/f UiSU+'V r* / Motor side mounting kit] •< 5 >77- LP^Y S 77'^L kKtttfte D^^-fey r-£&o£*y KT'To KSSt^TKtttf This kit can shorten the Actuator length with side mounting Motor shown in Photo right. Motor mount, timing pulley, timing belt and set screws are included in this kit. KSS can assemble in accordance with your reguest. Sensor accessories for the purpose of...

7STV K^7-</t Stepping Motor Driver DC24V Input Microstep Driver KSS provides you with suitable Stepping Motor Driver Recommended Steeping Motor Driver should be different depending on the Motor choice. iBiffim Output current Input signal Note 1) Micro-step angle for 1 pulse=Basic step angle/ Number of interpolation Note 2) Approx. 250pps is generated inside, regardless of splits setting ; CCW rotation when the dip switch NO.2 is ON , and CW rotation when the dip >$n$$SI / Connection diagrams iMffl^E— £ / Applicable Motor Brown (i)_CWLS (Short circuit insicieMTM) Brown/White(i/B) CCWLS...