High pressure gear pump KP 5
12Pages

Gear Pumps

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 1 Housing 2 Gearing 3 Drive shaft end 4 Flange cover 5 Roller bearing 6 Sliding plates 7 Lip-type shaft seal 8 Plain bearing 9 Housing gasket Technical Information KP series high pressure gear pumps are mainly used in oil-hydraulic plants. They are suitable both for hydraulic fluids as well as mineral oil bases (DIN 51524/25) and engine oils (DIN 51511). 1. External loads The robust design facilitates handling external radial forces, depending on the size and direction of application. The housing components are made from high-grade...

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 General Characteristics Calculation Formulas for Hydropumps Fixing type Flange type Characteristics, formula signs, units Pipe connection Flange; Dimensions, page 8 1 Discharge / displacement flow 2 geom. discharge / displ. flow Drive shafts Mounting position 9 hydr./ mech. efficiency Operating Characteristics Operating pressure Inlet port Outlet port Fluid temperature ϑm min = -- 20 °C ϑm max= + 80 °C for NBRLip-type shaft seal + 120 °C for FKM- Lip-type shaft seal Viscosity Recommended viscosity range Recommended values for...

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Displacement / Nominal Size Displacement Nominal size geom. displacement Speed range Permitted torques in N middle at shaft ends Mass inertia torque x 10-3

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Discharge Flow and Required Input Power Discharge flow at n = 950 1/min Discharge flow Q in 1/min at 34 mm2/s Pressure p in bar Required input power P in kW at n = 950 1/min Nominal size Discharge flow at n = 1450 1/min Discharge flow Q in 1/min at 34 mm2/s Pressure p in bar Required input power P in kW at n = 1450 1/min Nominal size Tolerance zone of the discharge flow: -- 5 % of table value Q. Select the delivery power of each drive motor approx. 20 % greater than table value P. If the viscosity is less than 30 mm2/s (cSt),...

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Type Key Ordering example KP 5 /160 C 1 0 K T 0 0 0 D E 1 /. Code for special design Seals 1 NBR lip-type shaft seal 2 FKM lip-type shaft seal Type of gearing E transmission made of case-hadening steel, hardened and bround Housing and bearing execution D Cast iron housing with multi component plain bearing Construction code 0 (internal allocation) Adaptor piece 0 without 2. Shaft end 0 without Shaft ends T Spline profile SAE-C, z = 14; DP 12/24 α = 30° V Spline profile W 40 x 2 DIN 5480 Z Cylindrical shaft Ø 38 Housing ports K...

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Nominal size Flange Type SAE-C-2 hole flange LA = 181; Ø z = 127

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Connections Housing side ports Inlet port 2 1⁄2" SAE connection (Ø 65) Housing side ports Outlet port 2" SAE connection (Ø 50) Shaft Ends Shaft end T Spline profile SAE-C Z = 14; DP 12/24, α = 30° Shaft end V Spline profile W 40 x 2, DIN 5480 Shaft end Z Cylindrical shaft Ø 38

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Accessory, Couplings Version A Gear rim off Polyurethane (Vulkollan) with 92° shore hardness Colour: natural Ordering code Hub material A G Coupling size Coupling size in Al (aluminium) in GG (cast iron) Lead bore Coupling hub length and hub bore Pump side cylindrical Finished bore Coupling hub length and hub bore Motor side zylindrical min. max. Mass Weight Mass Part Part Part Part Part Part moment moment 2 1 2 1 2 of inertia of inertia 1 2 2 Kgm Kg Kgm Ordering code Medium temperature: -- 10 °C up to + 80 °C (intermittent...

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5 Motor with Pump KP 5 / . C.0. Z00 0DE . Motor 4-pole Power Speed kW 1/min Motor 6-pole Power Speed kW 1/min Bell housing All motor dimensions and information refer to the ADDA motor make, other motor makes on request. Motor mounting IMB 35 All pump and motor sizes can be combined with each other

High-Pressure Gear Pumps KP 5 High Pressure Gear Pumps KP 5

Low and high-pressure gear pumps for lubricating oil, hydraulic, process and test bench applications, fuel and metering systems. I Flow Measurement Gear, turbine and screw type flow meters and electronics for volume and flow, metering and consumption in the chemical industry, hydraulic, process and test bench technology. I Hydraulics Single and multistage high-pressure gear pumps, gear motors and valves for construction machinery, municipal vehicles, agricultural vehicles, special vehicles and truck bodies. I Valves Cetop valves for all requirements stationary and mobile applications....