High-Pressure Gear Motors KM 5

High-Pressure Gear Motors KM 5 High Pressure Gear Motors KM5 1 Housing 2 Gearing 3 Drive shaft end 4 Flange cover 5 Rolling bearing 6 Sliding plates 7 Rotary shaft lip-type seal 8 Plain bearing 9 Sealing of the housing 10 Drain port Technical Notes: KM series high pressure gear motors are mainly used in oil-hydraulic plants. They are suitable both for hydraulic fluids as well as mineral oil bases (DIN 51524/25) and engine oils (DIN 51511). The housing components are made from high-grade cast iron, the shaft and gears from hardened and ground case-hardening steel. The shafts are supported in multi-layer...

High-Pressure Gear Motors KM 5 High Pressure Gear Motors KM5 General Characteristics Calculation Formulas for Hydropumps Fixing type Flange type Characteristics, formula signs, units Pipe connection Flange; Dimensions page 8 Drive shafts Mounting position Ambient temperature Working Characteristics Discharge/displacement flow geom. discharge/displ. flow Pressure Speed Torque Power Total efficiency Volumetric efficiency hydr./mech. efficiency Flow velocity Piping diameter = please see technical data = 40 bar Absorption capacity Drive torque Input power Volume flow Straight flange connection, hole...

High-Pressure Gear Motors KM 5 High Pressure Gear Motors KM5 Displacement / Nominal Size Displacement geom. Nominal Size displacement Vg cm3/r Working pressure Peak pressure Speed range Mass inertia torque Shaft end J kg m2 Permitted torques in N middle at shaft end (n = 1500 1/min) axial radial Performance data High Pressure Gear Motor KM5/219 at n = 750 1/min Delta p High Pressure Gear Motor KM5/250 at n = 750 1/min Delta p High Pressure Gear Motor KM5/300 at n = 750 1/min Delta p

High-Pressure Gear Motors KM 5 High Pressure Gear Motors KM5 Second shaft end 0 without Shaft ends / Load capacity of shaft T Involute spline SAE-C, z = 14; DP 12/24 α = 30°, 500 Nm max V Involute spline W 40 x 2 DIN 5480, 800 Nm max Z Cylindrical shaft Ø 31.75, SAE 1 1/4", Special number 194, 350 Nm max Adaptor piece 0 without Design serial no 0 (Specified by Kracht) Housing connection K 1 1/2" SAE connection (Ø 38) Outboard flanges or bearing resp. 0 without Code for materials Housing and bearing version D Cast iron housing with multicomponent plane bearing bushes Ordering example Type of gearing...

High-Pressure Gear Motors KM 5 High Pressure Gear Motors KM5 Displacement Nominal Size Flange Type SAE-C-4 hole flange E, ... /194 with leakage oil connection LA = 114.55; Ø z = 127

High-Pressure Gear Motors KM 5 High Pressure Gear Motors KM5 Connections Housing connection 11⁄2" SAE connection (Ø 38) deep Shaft Ends Shaft end T Spline profile SAE-C Z = 14; DP 12/24, α = 30° Shaft end V Spline profile W 40 x 2, DIN 5480 Shaft end Z Special number 194 Cylindrical shaft SAE 1 1/4" (Ø 31.75) Cylinder screw

High-Pressure Gear Motors KM 5

Low and high-pressure gear pumps for lubricating oil, hydraulic, process and test bench applications, fuel and metering systems. I Flow Measurement Gear, turbine and screw type flow meters and electronics for volume and flow, metering and consumption in the chemical industry, hydraulic, process and test bench technology. I Hydraulics Single and multistage high-pressure gear pumps, gear motors and valves for construction machinery, municipal vehicles, agricultural vehicles, special vehicles and truck bodies. I Valves Cetop valves for all requirements stationary and mobile applications. Pressure,...