MICROTRON SYSTEM MB 800
15Pages

KINEMATICA Homogenizing perfected. MICROTRON® MICROTRON® SYSTEM MB 800

OPERATING INSTRUCTIONS 1 Introduction This chapter gives information on the the structure of this document. It will assist you in making use of it and show how to find the required information quickly. Please read through these operating instructions before switching on or attempting to use the equipment. They describe the use of the MICROTRON® MB 800, its installation and maintenance and the appropriate replacement parts and accessories. They will help you avoid erroneous use and consequent damage. Although MICROTRON® machines are designed for ease of service, this does not release you...

2.1 Target Audience These operating instructions are intended for all authorised users of our machines/equipment. We distinguish different user roles, taking account of the different demands placed on the user by the activity to be carried out. You will find the definitions of user roles with the demands on the user in chapter "Safety". You can fulfil one or more of these roles, provided that you meet the corresponding demands.

OPERATING INSTRUCTIONS 2.2 Organisational matters If you are unable to find the answer to any question in the operating instructions, please contact the equipment manufacturer directly. 2.3 Location of the operating instructions The operating instructions can only be of use to you if you always have them to hand. They should, therefore, always be kept at the place where the equipment is used. E-Mail: info@kinematica.ch

2.5 Warning Notices Please be aware of the meaning of the following warning signs: Safety instructions must be observed to ensure safe operation This symbol indicates high voltage, with risk to health and environment

OPERATING INSTRUCTIONS Year of manufacture: A six digit appliance number is printed on the rating plate located on the bottom plate of the machine. The first two digits indicate theyear of manufacture for that machine. So that your able to enjoy using your MICROTRON® for a long time, please read these operating instructions before starting operation. It will assist you in avoiding malfunctions and damage. MICROTRON® units are maintenance friendly - which, however does not release you from proper inspections and above all from good cleaning. • Connect the MICROTRON® MB800 to an earthed...

KINEMATICA Homogenizing perfected. OPERATING INSTRUCTIONS The MICROTRON’ MB 800 can be just used for chop, beat, stir, mix, puree and emulsify of cuttable chemical materials/substances. The chemical and temperature Resistance of the used material (Glass, stainless steel, PP and rubber) has to be noticed in context with the blender.The process of explosive materials is strictly prohibited. It is forbidden to mix 2 materials which to not correspond with each other, or to get the mixture explosive because of overheating etc. If the MICROTRON’ MB 800 is used for any responsible for any damages...

7 Electrical Connection The power supply voltage must correspond to the values on the rating plate on the appliance (the voltage rating is given in volts (V)) The appliance should only be connected to a single phase grounded alternating current. Make sure that the original mains cable and the wall outlet correspond. The use of a faulty-energy-protection switch, (Fl) is suggested by all the works with electro-appliances. If at all possible, avoid using an extension cord. If it is unavoidable, only proper, approved extension cords should be used. Do not subject the mains cable to strong...

OPERATING INSTRUCTIONS 10 Safety Features and Motor Protection The safety control prevents the motor from being switched on when the protection cap/mixing lid is not in position and stops it if the protection cap/lid is raised during operation. When the protection cap/lid is replaced, the speed control knob must be turned back to "0" (reset function), before the motor can be restarted. ^ Only the speed control knob can be used to turn the machine on and off When the machine is overstressed or overheated, it switches off automatically. If this occurs, after about 60 seconds, please press the...

OPERATING INSTRUCTIONS The cutter head is made of stainless steel parts, which are actually very resistant. However, high temperatures and detergents generally reduce the lubricating effect of the grease in the built-in stainless steel ball bearings (with integrated NBR seals, heat resistant up to a maximum of 120° C). As a result, wear and tear-related failure often occurs sooner if the cutter head is treated in a dishwasher or an autoclave. Normally bearing damage initially only leads to a steady increase in noise of the mixer, so that the device is able to continue to work a long time...

OPERATING INSTRUCTIONS As a basic principle, no alcohol or solvents should be used to clean PMMA! A chemical resistance chart for PMMA can be downloaded here: https://adobe.lv/2lXBgrP (Document only available in German). In it you can see which chemicals are compatible with PMMA and which are not.

13 Repairs Obtain the address of your nearest KINEMATICA authorized service center from the store where you purchased your appliance. Bring your appliance to the service center or send it as a postage paid, registered package.

OPERATING INSTRUCTIONS Circuit board holder Motor safety switch Potentiometer with On/Off-Switch Motor brushes connection Stator connection Safety switch for cap surveillance Electronic Potentiometer connection for control device Suppressor screen filter EF-Choke Ground Neutral wire Mains supply Phase weiss blanc' white 'Motor motor .motor. schwarz 'noir / black cordon d'aUmentation mains supply

15 Warranty KINEMATICA AG guarantees that the equipment that it produces will run free of any fault related to materials or manufacturing faults for 24 months. ADDITIONAL WARRANTY FOLLOWING REGISTRATION Consumers who complete a warranty registration within 20 days of receiving their device will benefit from a free warranty extension of a further 12 months. This means that the total warranty period after registration is 36 months. If thorough testing shows a fault to be due to either of the above causes, KINEMATICA AG guarantees that the equipment will be repaired or replaced free of...