PBZ Series
20Pages

New simulation power source for more realistic and more flexible power reproductions ! Built-in function generator ! Capable of synchronized and parallel operation ! Intelligent Bipolar Power Supply 2 models: PBZ20-20 (±20V/±20A) and PBZ40-10 (±40V/±10A) CV100 kHz, CC10 kHz (PBZ20-20), 5 kHz (PBZ40-10) USB, GPIB, and RS232C provided (standard) ) LAN option available (complies with

New simulation power source for more realistic and more flexible power reproductions! function Sequence function Synchronized operation function Parallel operation function Unipolar mode High-speed response100kHz (CV) Low ripple noise! Intelligent Bipolar Power Supply ● USB, GPIB, and RS232C provided (standard) 　 LAN (option) The PBZ series is a series of bipolar DC stabilized power supply that can, without changing the output terminals, vary both the + and – polarity toward either side while continuously passing through zero. Four quadrants (bipolar) operation concept diagram Voltage...

Primary features/characteristics Intelligent Bipolar DC power supply Waveform generation function Built-in function generator! Easily create programs using user-defined waveforms! In addition to the basic sine, square and triangular waveforms, the PBZ series is equipped with a user-defined waveform generating function that can register up to 16 waveforms. It allows the amplitude, frequency, start phase, frequency sweep and square wave duty to be set as needed. The 16 user-defined waveforms can be freely edited, and the original created and edited waveforms can be registered and easily...

Primary features/characteristics The script function makes sequences even more convenient! The basic sine, triangular and square waveforms, as well as the 16 userdefined waveforms, can each be set as a sequence step, allowing even complex sequences to be created easily. Sequences are composed of up to 1024 steps. ● Concept diagram showing steps and program settings Program 1 This combination of steps forms a program, and the 1024 steps can be allocated and set in a maximum of 16 programs. When executing sequences, in addition to executing a single program, the script function also allows...

Parallel operation function Easily expand the capacity This function expands the output current. It allows multiple units to be connected in parallel according to the required current. With 2 standard units of the same model and the optional parallel operation kit, the user can easily complete the setup. Although up to 5 units can be operated in parallel, if 3 or more units will be used, please consult with us. PK01-PBZ 2 OUTPUT ■ Parallel operation kit (option) Intelligent Bipolar DC power supply Operation in the full quadrant 2 area Unipolar mode This is a function unique to this product....

Other features/characteristics 40% lighter than previous models Response switching Weight: Approx. 22 kg. A large reduction in weight was achieved by using a Switching + Linear system. This contributes to improved workability not only on bench-tops, but also when test environments are moved. In both CV and CC mode, the 4 ranges can be switched. Expanded measurement functions The built-in measurement functions allow testing without the multimeter and other measurement devices that were previously needed. In addition, the measurement time TRIG signal allows the measurement start and...

series Intelligent Bipolar DC power supply Soft start and soft stop function Output voltage/current monitor With soft start, when output is changed from OFF to ON, a soft-start time is applied at startup from when output is 0 to when the DC set value is reached. With soft stop, when output is changed from ON to OFF, a soft-start time is applied at stop from when output is the DC setting to when the output reaches 0. V ● oltage monitor Rear panel (J1 connector) 0 to ±2V from 0V to ± rated voltage Soft start and stop times can be set only for the DC setting value. If the OUTPUT key is pressed...

Specifications Unless specified otherwise, the specifications are for the following settings and conditions. • The warm-up time is 30 minutes (with current flowing). • TYP value: hese are typical values that are representative of situations where the PBZ operates in an environment with an ambient temperature of 23 ºC. T These values do not guarantee the performance of the PBZ. • rating/CF: The rated voltage or rated current divided by CF (crest factor). • The polarity of the output voltage and current is defined as follows. Voltage: Using the output’s COM terminal as a reference, the...

series Intelligent Bipolar DC power supply Measurement display function Measurement range (resolution) DC Accuracy *1 Temp. coefficient Measurement AC range (resolution) Voltage DC AC Measurement range (resolution) measurement AC, DC AC Accuracy *1, *2 PEAK PEAK DC Measurement range (resolution) Accuracy *1, *3 Measurement range (resolution) Accuracy *1 Temp. coefficient Measurement AC range (resolution) Current measure- DC AC Measurement range (resolution) ment AC, DC AC Accuracy *1, *2 PEAK PEAK Measurement range (resolution) Accuracy *1, *3 Measurement time Common speci- Software...

Option ■ Sequence creation software 　 　 Wavy for PBZ NEW [Operating environment] Windows 2000 / Windows XP / Windows Vista / Windows 7 *For details, please see our company’s homepage. This software further strengthens the waveform generation and sequence functions of the PBZ series. Create and edit in two ways: either by drawing with the mouse or spreadsheet style. ▲ U ser-defi ned wavefor m edi t screen ● This software allows easy creation and editing of the test condition data that is necessary for sequence operation. ● The function for saving test condition data files makes it easy to...

Rear panel Intelligent Bipolar DC power supply 4-M3 screw hole (Max. screw insertion depth 8 mm) 4- 5 (Rubber foot installation hole) External dimensions diagram 8-M4 screw hole, including opposite surface (Max. screw insertion depth 6 mm)