Group: KHS Gruppe
Catalog excerpts
1 KHS INNOPET® BLOMAX SERIES IV STRETCH BLOW MOLDING MACHINES The InnoPET Blomax Series IV has an output Blomax Serles IV Is available In a modular design of 4 to 36 blowing stations, each with an output rate of up to 2,200 PET bph The standard production of the InnoPET Blomax Serles IV Is a bottle volume of 0.2 to 3.0 liters. Special sizes can also be produced During the development of all technlca nnovatlons within the InnoPET Blomax Serles IV, special emphasis was placed on key requirements like minimum energy consumption, process stability as well as uptime. The focus and goal of the develop- ment were lowest total cost of ownership per produced bottle. All technical Inno- vations Integrated Into the Serles IV support this goal • Exclusive use of short-wave, energy-dense NIR (Near Infra Red) radiation • Heatlng-up time of preforms reduced by 50% • Reduction of surface heat • Re-heat and cooling energy consumption reduced by approx. 30% vs. traditional heating technology The new CLever-Loc blow molding stations • minimum footprint design, more stations on the same blowing wheel diameter • only one half opens, the other half remains rigid • CLever-Loc device, clamping through toggle • Longer process time • Higher specific output of up to • Compatible with Series III molds Preform transport via active mandrel and TouchGrip system • Improvement of the established mandrel system: Active mandrel transports preforms gently and securely through the oven • Gripper of TouchGrip systems take over Servo-driven StretchFlexx stretching system • Stretching speed Independent of machine speed • Servomotors control the stretching rod • Rapid change-over, no mechanica • Stretching movement and -speed can be • High process stability • Less scrap Compressed air savings with Eco-Space valves • Approx. 15% decrease of top Industria values In compressed air consumption through redesign of valve block • Approx. 25-30% savings of blowing air through reduced dead air volume • Alrback air recycling Internally or externally • Reduction of wear parts • Central axis of blowing station with permanent lubrication • Automatic central lubrication • No adjustment of guldlngs and transfers • Large doors, easy accessibility • Up to 25% savings In change-over time • Run-up time only approx. 15 sec More efficiency in blocked systems • Easy Interlocking with suitable fillers/caps to an InnoPET BloFIII block • Short start-up time • 50% less preform scrap after emergency stop • Improved adaptation to filling output through Independent stretching • Enhanced product quality Reference of all values is made in comparison to Series III Filling and Packaging - Worldwide
Open the catalog to page 12 KHS INNOPET BLOMAX SERIES IV STRETCH BLOW MOLDING MACHINES *) dependent on preform and bottle design **) cam modification bottle output ***) larger diameters on request Filling and Packaging - Worldwide
Open the catalog to page 2All KHS GmbH catalogs and technical brochures
-
KHS GEAR FLUID 220
2 Pages
-
KHS HEAVY DUTY GREASE 03
2 Pages
-
KHS GEAR FLUID 460
2 Pages
-
KHS GEAR FLUID PG 220
2 Pages
-
KHS MULTI GREASE 01
2 Pages
-
GEAR FLUID 220
2 Pages
-
BEARING GREASE 06
2 Pages
-
MULTI GREASE 01
2 Pages
-
INNOKET NEO
2 Pages
-
INNOFILL GLASS DPG
2 Pages
-
1_INNOKEG CONTIKEG
2 Pages
-
1_INNOKEG TRANSOMAT
2 Pages
-
1_INNOPET BLOFILL
2 Pages
-
1_INNOPET FRESHSAFE BLOCK
2 Pages
-
Innokeg AK keg
2 Pages
-
Innopro Paramix C
2 Pages
-
InnoPET Plasmax
2 Pages
-
Innoline PTR pallet conveyor
2 Pages
-
Innopal AS-1-N depalletizer
2 Pages
-
Innopal PBN (H) palletizer
2 Pages
-
Innopal RK articulated robot
2 Pages
-
Innocheck FHC (Infrared)
2 Pages
-
Innocheck FHC (Gamma)
2 Pages
-
Innocheck Superblock
2 Pages
-
Innocheck ECI
2 Pages
-
Innocheck Compact Selecta
2 Pages
-
Innokeg Till AK
2 Pages
-
Innoclean KW
2 Pages
-
Innofill PET DVF
2 Pages
-
Innopro HF
2 Pages
-
Innopro ACF
2 Pages
-
Innopal AS-1-H depalletizer
2 Pages
-
Innocheck BSS bottle sorter
2 Pages