Catalogs >
Key Technology (China) Limited >
K-TEK-V342KP-FN-AC datasheet

K-TEK-V342KP-FN-AC datasheet
16Pages

Catalog excerpts

Head Office:B703,Building l,Tianan Cyber Park,Huang Ge North Road,Longcheng Subdistrict,Long Gang District,ShenZhen,Guang Dong, I Factory ADD.: Floor 7, Building S8, Fenggang Tianan Cyber Park, No. 208 Fenggang Section, Dongshen Road, Fenggang Town, DongGuan, Guang Dong, Tel:+86 755 89239859,89230460,85232807 Fax:+86 755 89312576 E-mai I :i nfo@key-tek.cn, sales01@key-tek.cn Website: www.key-tek.cn, www. rugged-key.com Model NO.: K-TEK-V342KP-FN-AC DESCRIPTION: 101 keys IP54 static sealed & ruggedized industrial ultra thin matrix keyboard with 12 function keys on top line for easy operation, and numeric keypad on right side, industrial level module with Scissors switch technology with long stroke (1.6mm) with extremely good tactile feeling for fast and accurate data input without any noise, with mounting holes on the edge for rear panel mounting, industrial Level. DIMENSIONS: 341.98mm x 114.0mm

Open the catalog to page 1

APPLICATIONS: This keyboard provides full-size versatility in a rugged, compact design with the embedded convenience. This keyboard is ideal for use in environments ranging from manufacturing to material handling to military settings. MATERIAL HANDLING: mobile keyboard, data entry, assembly line etc MILITARY: Military laptop, Army, Navy, Airforce INDUSTRIAL: Industrial automation, pharmaceutical, oil and gas, food and beverage, clean or dirty manufacturing environments, warehouses OTHER INDUSTRIES

Open the catalog to page 2

Environmental Condition Measurement Conditions The measurements shall be made the following standard conditions. Temperature of measurements: 5～35°C Humidity of measurements:45～85%Rh Pressure of measurements: 860～106

Open the catalog to page 3

Temperature of measurements: 20±2°C Humidity of measurements: 60^70%Rh Pressure of measurements: 860^1060hPa Mechanical Characteristics

Open the catalog to page 4

Operating Travel: 1.1±0.2mm Maximum Travel: 1.6± 0.2 mm(force at 120g)

Open the catalog to page 5

Set the keyboard vertically. Pull the keycap in the opposite direction until it comes off and the load shall be measured. All side load: 9.8N (1000gf) or more.

Open the catalog to page 6

Periphery of a keycap at a rate of free drop. Key in test spec on the 4-corners area of the keycap put 70g poise on each corner of keycap to see if it can act. Note: Adjacent key is untouchable at any circumstances during normal operation; Must use Pin gauge ^5.0mm. Keycap Periphery Pressing Operating force: Must be “ON” within the maximum peak force of keycap center pressing. Click feeling: Must be a click feeling.

Open the catalog to page 7

Other key bigger than normal key except space bar Keycap Periphery Pressing All the keys smaller than normal key

Open the catalog to page 8

There is no warp production for this model, but curve condition can be acceptable. Keyboard Warp Satisfy to the table as follows. Nature Distortion Size. Keycap shift Shall be no more than 0.4mm in either X or Y directions.

Open the catalog to page 9

Keycap twist Keycap slant Conditions 测试条件 Specification 判定标准 Less than 0.5mm between neighboring keys. 12 Keycap height alignment Less than 0.5mm in neig

Open the catalog to page 10

Electrical Characteristic

Open the catalog to page 11

Push the center of the keycap to the full stroke continuously 10 times by keystroke rate of 4 times/sec, and measurement maximum value. Endurance (Keyboard Unit)

Open the catalog to page 12

To perform on the flat cable or other portion need winding shall withstand winding test on a mandrel 1mm diameter of 180 angle ending 5 cycles with load 2Kg between the surfaces. Flexure strength of membrane tail The resistance shall be within 150% of initial value. Electrical characteristic passed. Hardness Test 1. Coverage: Naked carbon 2. Taster: Pencil hardness tester 3. Test method: Put 2H pencil on the pencil hardness tester, 1Kg load, row 5 for 3 to 5mm line, then erase the lines with eraser. lKg Test surface can not have a obvious scratch, carbon no cutting.

Open the catalog to page 14

Precaution for Handling Connection to the connector. 1. Recommended connector is “ ZERO FORCE TYPE ”. Please be sure to avoid the connectors that scratch on the surface of flexible pattern. 2. Excess force to the flexible pattern shall be prohibited at the time of insertion. 3. Allocation of connector is recommended to be as close to the edge as possible. If impossible, please be sure to keep it apart from hot components. 4. Please consider the allocation of connector not to be installed as below. If unavoidable, please be sure to keep R3 Min.

Open the catalog to page 16

K-TEK-V342KP-FN-AC datasheet 16Pages

Catalog excerpts

All Key Technology (China) Limited catalogs and technical brochures

K-TEK-V342KP-FN-AC datasheet
16Pages