Technical Datasheet ZHM CT Series Gear Flow Meters in Cartridge Design for paint applications, optimized flushing and weight design Certified according to DIN EN ISO 9001

Gear Flow Meters – ZHM CT Series Overview With more than 50 years of experience in the flow measurement field and numerous innovative and customer-specific product developments, we are a qualified and competent contact for flow measuring technology and calibration. KEM offers a broad selection of measuring principles for this purpose. We develop, produce, and deliver high quality Gear Flow Meters, Turbine Flow Meters, Helical Flow Meters and Micro Flow Meters as well as Coriolis Mass Flow Meters worldwide. Specific accessories complement the product range. This document provides information,...

ZHM CT Series – Gear Flow Meters The ZHM CT gear flow meter series (cartridge design) are flow meters which are mainly used in water- and solvent-based paints, as well as fillers and base coats. Also suitable for cavity waxes and for abrasive and filled media in the automotive sector. Short response times, accurate dosage, and flow rate measurements support applications in coating lines and preservation and other coating systems. Only high-grade steels that even withstand corrosive liquids are used in the production of gear flow meters. Combined with the use of tungsten carbide bearings, the...

Gear Flow Meters – ZHM CT Series Technical Data – Sizes ZHM Type2) Measuring Range (l/min) Technical Data – General Measuring Accuracy ±0.05 % (under the same conditions) ±0.5 % of actual flow (viscosity ≥ 30 mm²/s) Housing: Wheels: Bearing: Seals: Medium Temperature See dimensional drawing (page 5 to 6) as per DIN 1.4305 [AISI 303] as per DIN 1.4122 Tungsten carbide sleeve bearing, stainless steel ball bearing PTFE (others on request) Exact type designation see ordering code (page 7). Average values for single sensors, dual pickups and higher resolution available. 4) Under laboratory conditions;...

ZHM CT Series – Gear Flow Meters Dimensional Drawing – ZHM 01/1 to 01/2 with lateral process connection 2x Others on request. Only applies for single pickup holes of type „E“. Attention: the total installation height is the result of the height (H) and the height of the electronics (dimensions in separate datasheet). 5) 6) Original KEM Document: ZHM_CT_D_EN_220101_E001 | Copyright

Gear Flow Meters – ZHM CT Series Dimensional Drawing – ZHM 01/1 to 01/2 with bottom inlet Only applies for single pickup holes of type „E“. Attention: the total installation height is the result of the height (H) and the height of the electronics (dimensions in separate datasheet). 7) Original KEM Document: ZHM_CT_D_EN_220101_E001 | Copyright KEM, Subject to cha

ZHM CT Series – Gear Flow Meters Ordering Code ZHM - XX Measuring Range Meter Attributes Bearing sleeve bearing ball bearing9) sleeve bearing ball bearing9) Thread bottom in-/outlet8) bottom in-/outlet8) BSPP BSPP M14x1.5 Plug-in (frequency doubling, bidirectional measurement)10) Plug-in (ESTA fiber optic) Sealing Options PTFE (Teflon®) Flat gasket PTFE (Teflon®) Mounting plate with flat gasket PTFE, Pmax. 40 bar [580 psi] Pressure Drop Curves Bottom inlet with flat gasket PTFE, Pmax. 40 bar [580 psi] Size ZHM 01/1 not available. 10) Pmax. 100 bar [1,450 psi]. 8) 9) Original KEM Document: ZHM_CT_D_EN_220101_E001...

Gear Flow Meters – ZHM CT Series Calibration In-house calibration is performed on volumetric calibration rigs or in our DAkkS calibration laboratory, depending on the needs of the client. The KEM calibration lab uses a high-precision load cell system. With an accuracy of 0.05 % for the mass and 0.1 % for the volume of flowing liquids, we occupy a leading position worldwide. The German Accreditation Body (DAkkS) has accredited the laboratory engineers, processes and measuring equipment in accordance with the international standard DIN EN ISO/IEC 17025:2018. The KEM calibration certificate not...

Liebigstraße 5 85757 Karlsfeld Germany Wettzeller Straße 22 93444 Bad Kötzting Germany Liebigstraße 5 85757 Karlsfeld Germany Wettzeller Straße 22 93444 Bad Kötzting Germany More distributors & partners can be found at: www.kem-kueppers.com KEM Küppers Elektromechanik GmbH | Liebigstraße 5 | D-85757 Karlsfeld | Tel +49 8131 59391 - 0 | Fax +49 8131 92604 Original KEM Document: ZHM_CT_D_EN_220101_E001 | Copyright KEM, Subject to change without n