Tank Contents Measurement System "Castello"
2Pages

{{requestButtons}}

Catalog excerpts

Tank Contents Measurement System "Castello" - 1

Content Measurement System for ventilated or pressurised tanks Castello offers a user-friendly way to re­ resent the pressure measurement at the bottom of a p tank as the quantity of remaining liquid. At the push of a button, the micro­controller performs the calculations using the information of the tank shape and dimen­ ions and displays the res maining tank content quantity on the clearly legible 5-digit LED display in the desired unit (litres, gallons etc.). The unit is configured using a PC and the easy-to-use software so that the filling level, which d ­ etermines the pressure, can be converted into an appropriate filling quantity. First the tank s ­ hape is selected, then the tank dimensions and the specific gravity of the liquid are entered. It contains the most current tank shapes. The program covers the most common tank shapes, but also enables any shape by entering the parameters into a specified table. The exclusive use of absolute pressure sensors in the Castello system eliminates the use of capillary vented cables with all the problems associated with a gauge pressure measurement. The Castello housing integrates an air pressure sensor, ranged between 0,8 bar and 1,2 bar absolute. The sensors to measure the hydrostatic pressure at the bottom of the tank are calibrated from 0,8 to 1,8 bar abs for tanks up to 5 m in height, and 0,8 to 2,3 bar abs for tanks up to 10 m in height. The pressure difference, calculated by the micro­-controller, is the relative hydrostatic pressure. The content of a pressurised tank is determined using the difference between the measurements from two absolute pressure sensors located at the top and bottom of the tank. The overall accuracy of the system of 2 mbar is achieved using a computerised calibration and compensation procedure for the pressure sensors. The coefficients for this calculation are stored in EEPROMs in the sensors. These are retrieved by the micro­ rocessor at each meap surement and employed within the equations to calculate the pressure values. The Castello housing and hydrostatic sensor can be interchanged at will. It is also possible to connect a standard 3-wire transmitter or high-precision digital transmitter (Series 36 X) that can be configured to an accuracy of 0,02 %FS over a range of 0 to 50 °C, a true representation of which is displayed by the Castello. Binder male socket 8 pole / Serie 723 The power supply to the system (8 to 28 V) can be provided externally or internally using a 9 V battery. The display is obtained by pressing the button on the front, and the ­ alue appears v for a configurable duration. The Castello has two switch outputs with configurable functiona­ity l and threshold values. An external power supply must be provided if the switch outputs are used. Side View Indication of switching outputs (LED) Optional: second transmitter Diaphragm’s position Bottom View KELLER AG für Druckmesstechnik CH-8404 Winterthur +41 52 235 25 25 info@keller-druck.com Drill holes for mounting KELLER Ges. für Druckmesstechnik mbH DE-79798 Jestetten +49 7745 9214 0 eurocenter@keller-druck.com Edition 04/2018 Subject to alterations Companies approved to ISO 9

Open the catalog to page 1
Tank Contents Measurement System "Castello" - 2

Installation There are two holes in the housing for mounting the unit. To install the sensor, unscrew and remove the cover of the unit, lead the cables through the PG screw connections and attach the wires to the screw terminals. The Castello is programmed via the connector on the side, which is also the location of the external power supply and switch output connections. Provided that the cover and the cable leadthrough are securely tightened, the extremely robust housing is watertight in compliance with IP65. Castello Ordering Information Castello basic unit + KELLER standard transmitter...

Open the catalog to page 2

All KELLER catalogs and technical brochures

  1. ECO2

    5 Pages

  2. ARC-1

    7 Pages

  3. KELLER

    36 Pages

  4. Series 26 Y

    2 Pages

  5. Series 26 W

    1 Pages

  6. Handpump K/P

    1 Pages

  7. K-114 BT

    3 Pages

  8. K-114

    3 Pages

  9. 21 ge

    1 Pages

  10. LEO 3

    1 Pages

  11. FA-23

    1 Pages

  12. Series 8

    2 Pages

Archived catalogs