Catalog excerpts
• TDSET3 Ethernet compliance testing o Automated compliance testing for 10,100, and 1000BASE-T PHY o Designed for use with MSO/DPO5000, DPO7000, and DPO/DSA/ • SR-ENET Ethernet triggering and analysis o Automated trigger (MSO/DPO5000 Series only), decode, and o Designed for use with MSO/DPO5000, DPO7000C, and DPO/DSA/ • DP04ENET Ethernet triggering and analysis o Automated trigger, decode, and search for 10BASE-T and Tektronix offers comprehensive, integrated tool sets for validating the physical layer of IEEE 802.3 Ethernet devices, and for developing and debugging Ethernet-based systems. The Tektronix TDSET3 Ethernet Compliance Test application (Opt. ET3) and selected Tektronix oscilloscopes provide one-button testing for 10/100/1000BASE-T test suites as specified by the IEEE standard for compliance testing. TDSET3 automates compliance testing and allows engineers to perform the required tests efficiently and reliably right on the The Tektronix MDO4000 Series oscilloscopes with the DP04ENET Serial Application Module and MSO/DPO5000, DPO7000C, DPO/DSA/ MSO70000C/D/DX/SX Series oscilloscopes with the SR-ENET application simplify analysis of Ethernet waveforms when validating and debugging Ethernet-based systems. The DP04ENET and SR-ENET applications offer automated trigger, decode, and search for 10BASE-T and 100BASE-TX Ethernet, enabling fast and efficient validation and debug. o Designed for use with the MDO4000 Series oscilloscopes
Open the catalog to page 1Datasheet TDSET3 – Automated Ethernet physical layer compliance testing Wide range of tests Ethernet compliance testing has some unique measurement challenges: Generating the “disturbing” signal requires tools to generate both pattern data and noise to provide real-world noise for return loss measurements There are many individual amplitude, timing, return loss, and template tests required for each Ethernet variant: The 10BASE-T standard specifies 22 tests per port plus fault tolerance and CMRR The 100BASE-TX standard outlines 12 tests per port plus CMRR and more The 1000BASE-T standard...
Open the catalog to page 2Ethernet 10/100/1000BASE-T Application Software — TDSET3 • SR-ENET • DPO4ENET Jitter tests Test fixtures Jitter tests quantify the timing variations of the edges of the signal, using specified test patterns. These jitter measurements include the contributions from duty cycle distortion and the baseline wander. Jitter is determined by accumulating waveforms, measuring the width of the accumulated points at the eye crossing, and the peak-to-peak is inferred from minimum and maximum values in the tails of the histogram. For example, the preceding figure shows the jitter measurement on a...
Open the catalog to page 3Debugging Ethernet-based embedded systems designs provides some complex measurement and analysis challenges: • Capturing specific Ethernet addresses and data • Displaying the elements of the Ethernet message in an understandable format, in a variety of formats, for a wide variety of engineers and • Time-correlating Ethernet messages with analog and digital signals in • Capturing long time windows of Ethernet traffic and then finding specific events within the acquired data The optional SR-ENET application software, installed in an MSO/DPO5000, provides a robust set of tools for debugging...
Open the catalog to page 4Ethernet 10/100/1000BASE-T Application Software — TDSET3 • SR-ENET • DPO4ENET 100BASE-TX decoded Event Table showing all packet information with time stamp information 10BASE-T and 100BASE-TX search Triggering is very useful for isolating the event of interest, but once you’ve captured it and need to analyze the surrounding data, what do you do? In the past, users had to manually scroll through the waveform counting and converting bits and looking for what caused the event. With the SR-ENET application installed, you can enable the oscilloscope to automatically search through the acquired...
Open the catalog to page 5Datasheet DPO4ENET – 10BASE-T and 100BASE-TX triggering and analysis Debugging Ethernet-based embedded systems designs provides some complex measurement and analysis challenges: Capturing specific Ethernet addresses and data Displaying the elements of the Ethernet message in an understandable format, in a variety of formats, for a wide variety of engineers and technicians Time-correlating Ethernet messages with analog and digital signals in the embedded system Capturing long time windows of Ethernet traffic and then finding specific events within the acquired data Color-coded DPO4ENET...
Open the catalog to page 6Ethernet 10/100/1000BASE-T Application Software — TDSET3 • SR-ENET • DPO4ENET 10BASE-T and 100BASE-TX event table In addition to seeing 10BASE-T and 100BASE-TX decoded data on the bus waveform itself, you can view all captured packets in a tabular view much like you would see in a software listing. Packets are time stamped and listed consecutively with columns for each component (Time, Destination Address, Source Address, Length, Data, FCS/CRC, and Errors). 10BASE-T and 100BASE-TX packet content triggering is very useful for isolating the event of interest, but once you’ve captured it and...
Open the catalog to page 7Specifications TDSET3 compliance test characteristics General mask Autofit, Waveform/Sample Count. Instrument compatibility Ethernet standards Recommended oscilloscopes for compliance testing (Windows 7 versions only) MAU Ext (and inverted), MAU Int (and inverted), Link Pulse, and TP_IDL Differential voltage, common mode output voltage With and without cable Return Loss Positive and negative polarity Signal amplitude, amplitude symmetry, differential output voltage, waveform overshoot Time Domain Tests Rise Time, Fall Time, Rise/Fall Time Symmetry Jitter and duty cycle distortion Return...
Open the catalog to page 8Ethernet 10/100/1000BASE-T Application Software — TDSET3 • SR-ENET • DPO4ENET TDSET3 compliance test characteristics Test Master (filtered and unfiltered), Slave 3 (filtered and unfiltered) Return Loss SR-ENET Ethernet triggering and analysis test characteristics Instrument compatibility Ethernet standards Recommended oscilloscopes Bus setup options Option Ethernet compatibility Analog channels 1-4 Math channels 1-4 Recommended probing Address/data formats available Hex Binary Hex or ASCII: Data Mixed: Hex or ACSII data, other fields in decimal and hex. Ethernet data rates Decode display...
Open the catalog to page 9All Keithley Instruments catalogs and technical brochures
-
6220-6221
5 Pages
-
6482
3 Pages
-
2520
8 Pages
-
2606B
13 Pages
-
2601B
20 Pages
-
AFG1000 Series
13 Pages
-
AFG31000 Series Datasheet
22 Pages
-
2182A Nanovoltmeter
6 Pages
-
6 Series B MSO
69 Pages
-
Isolated Measurement Systems
8 Pages
-
TBS1000B-EDU Series
14 Pages
-
3 Series MDO
36 Pages
-
4 Series MSO
40 Pages
-
TSG4100A Series
24 Pages
-
2461-EC Graphical Potentiostat
16 Pages
-
2460-EC Graphical Potentiostats
15 Pages
-
2450-EC Graphical Potentiostat
15 Pages
-
4200A-SCS Parameter Analyzer
45 Pages
-
MDO4000C Series Datasheet
43 Pages
-
RTPA2A
6 Pages
-
TPA-N-PRE Datasheet
4 Pages
-
DPO4PWR·MDO3PWR Datasheet
6 Pages
-
DPO4LMT/MDO3LMT Datasheet
6 Pages
-
DPO7000 Series Datasheet
28 Pages
-
SourceXpress® Datasheet
4 Pages
-
10G-KR Datasheet
8 Pages
-
DPO70000SX Series Datasheet
46 Pages
-
AWG4000 Series Datasheet
20 Pages
-
TLA6400 Series Datasheet
14 Pages
-
Potentiostats 2450-EC
8 Pages
-
4200-SCS
16 Pages
-
2013 Keithley product catalog
403 Pages
-
Nanotechnology Measurement
13 Pages
-
Semiconductor Device Test
11 Pages
-
Series 2400 SourceMeter®Family
16 Pages
Archived catalogs
-
8 Series Sampling Oscilloscope
14 Pages
-
Multimeter/Switch System
1 Pages