Pallet pull-outs universal · pole-mounted KARL H. BARTELS GmbH Info-Tel.: +49 (0)4126 3968-333 [email protected]

Pallet pull-outs Pullout Units – universal Universal units - for mounting on the carrying beams in pallet racks or directly on the fl oor. - Provides maximum ergonomic handling of your picking goods, then the load surface is easily accessible from three sides, thus reducing the burden on the shoulders and backs. - Creates economic benefi ts when the number of picking locations can be increased, then the minimum clearance required to above present carrying beam. - A large number of models to cover most needs in terms of usage, load and extract capabilities. on page 3 Pullout Units - pole-mounted...

Pallet pull-outs universal 5 BARTELS Shelf drawer for pallet rack • Turns a pallet rack into a shelf drawer rack • Suitable for almost all common pallet racks • Convenient access on or in pallets or boxes without needing a pallet truck or forklift • Ergonomic working postures, without acrobatics and athletic efforts • Potential space-saver through narrow aisle widths • Safety through pull-out lock • Optionally with 600 kg or 1000 kg load capacity, pull-out on one side or both sides. Design: Rugged steel construction, ball bearing guides, delivery includes fasteners. Standard colour blue RAL 5010, additional...

Pallet pull-outs universal 5 BARTELS 2-way pull-out unit that can be extended in two directions! • The unit can be pulled out and loaded from the „back“ and pulled out by the operator at the ,front‘. KARL H. BARTELS GmbH Info-Tel.: +49 (0)4126 3968-333 [email protected]

Pallet pull-outs universal 5 BARTELS Pullout Trolley for floor mounting Open model that can be loaded with pallet lifters. Handle on the right side with locking function. Pullout unit for stand-alone floor mountingNo clearance under the unit Type

Pallet pull-outs universal 5 BARTELSRear plate Design: Plate mounted at the rear of the drawer slide. The plate serves to act as load restraint when you have goods that can easily fall off if the unit is pushed with too much speed when it hits the stop. Height 500 mm. Galvanized. Installed with self-tapping screws. KARL H. BARTELS GmbH Info-Tel.: +49 (0)4126 3968-333 [email protected]

Starting assistance for beam mounted extraction units A gas spring helps the unit up and running when it should be pulled out, reducing power significantly. (To push back the device is normally easier) Can be selected as an option on the following types: UE-670.2, UE-870, UE-17415, UE-17425, UE-16604(-L), UE-16606(-L) KARL H. BARTELS GmbH Info-Tel.: +49 (0)4126 3968-333 [email protected] Pallet pull-outs universal

Pallet pull-outs universal 5 BARTELS Floorset Simple conversion of a shelf drawer into a bottom drawer Floor set „standard“: With floor set ..standard" creates space of 100 mm below the unit, which allows it to be loaded with, for example with support leg forklift . Mounts with anchor bolts 10 * 80 Colour: silver RAL 9006 Floor set „low“: is used when the pull-out unit to be mounted free-standing on concrete floors with minimum building height. With floor set “low” you get a low-profile unit and saves 100 mm compared with floor set standard.. There is no free space under the unit which means...

Pole-mounted pull-out-unit suitable for Meta-pallet racks for all ordinary pallet racks on request Pullout Units - pole-mounted Units with very low height for direct installation in the rack uprights • Extreme saving of shelf height since no crossbeams are required, inserted directly into pallet frame • Turns a pallet rack into a shelf drawer rack • Suitable for almost all common pallet racks • Convenient access on or in pallets or boxes without needing a pallet truck or forklift • Ergonomic working postures, without acrobatics and athletic efforts • Pull-out lock in standard positions, released...

Pole-mounted pull-out unit with a pullout of 90% of the load surface Pole-mounted pull-out unit with ball-bearing support wheels in the front that goes to the floor. Equipped with side support bearings that ensures maintenance-free operation. Racking frames must be bolted to the floor and support beams mounted on a maximum height of 2000 mm in order to ensure that proper bracing laterally and clear opening dimensions between uprights always achieved. Handle 350 mm is included, increased price for 550 mm see page 12. The loading area Total 2-way pole-mounted pull-out unit that can be extended...

Pole-mounted pull-out-unit suitable for Meta-pallet racks for all ordinary pallet racks on request 2-way pole-mounted pull-out unit with edge around Can be pulled out backward / forward .Secure in the retracted position, grip the edge of the front. Racking frames must be bolted to the floor and support beams mounted on a maximum height of 2000 mm in order to ensure that proper bracing laterally and clear opening dimensions between uprights always achieved.

5 BARTELS Shelf Max distributed load: 350 kg Galvanized sheet metal foil mounted on the drawer slide when you want a flat surface to directly store cartons, boxes or similar items. Mounted to the pullout unit with spacers and adhesive pads. KARL H. BARTELS GmbH Info-Tel.: +49 (0)4126 3968-333 [email protected]