PERMANENT ELECTROMAGNETIC CHUCKS
9Pages

PERMANENT ELECTROMAGNETIC CHUCKS Model EP-Q PERMANENT ELECTROMAGNETIC CHUCK FOR CUTTING ELECTROMAGNETIC CHUCK PERMANENT PERMANENT PERMANENT CHUCKS CONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKS ELECTROMAGNETIC CHUCKS A Line-up of products selectable according to machining methods and workpieces. ■Considerable power saving and reduction in size of the Chuck Master by the renewed design. ■The detachable connector type is employed to respond to pallet changing. ■Electricity is used only when mounting and demounting workpieces. Workpieces can be held firmly in the event of power failure. ■Usable in wet machining operations. An example of machining by use of straightening block ［Application］ Suitable for securing workpieces during cutting on milling machines and machining centers. ●Magnetization and demagnetization in a very short time. ●Tapped holes on the attractive face can be used to install various blocks to hold workpieces by various methods according to machining operations. ●Straightening blocks are also available that are mounted on the chuck work face to hold workpieces by an induction field. These optional products are very useful for workpieces having irregular attractive faces that for example have steps and distortion and for machining the bottom and side faces of workpieces. (See ■Options on page 32.) ■EP-QN Series PROMELTA* SYSTEM VACUUM CHUCKS ［Features］ ●The power cord is of detachable connector type for easy use. The connector cap is of waterproof type. ●Can be used in wet machining operations. ●The chuck is very thin, 70 mm in height, and light weight. ●Less accuracy change and highly rigid construction. ●Considerable power saving compared with conventional products. (□70: 50% reduction, □50: 70% reduction) Power saving Minimal heat generation Work Face BLOCKS, HOLDERS, MINI CHUCKS Mounting Face Tapped Hole on Attractive Face Pole Dimensions Environmentally friendly Chuck controller required additionally Standard Size Model Applicable   Chuck Master ■EP-QS Series HOLDING TOOLS ※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat. MEASURING TOOL HOLDERS Power saving Minimal heat generation Work Face Standard Size Model Environmentally friendly MAGNETIC TOOLS ［mm （in） ］ Tapped Hole on Attractive Face Mounting Face Pole Dimensions MAGNETIC HOLDERS Chuck controller required additionally

■EP-Q type holding power characteristic M' 1]' Chuck size 3060A Normal (Ribs arranged between poles) Pole size Strong (Poles arranged densely) ^•••□50 7--O70) <Ordering information> •Sizes other than the standard sizes listed on page 31 are also available. •The recommended maximum one-piece size is W1200 x L1500 mm. For other larger sizes, please contact us. •Round chucks are also available. •When workpieces are hardened steel or special steel, they may be difficult to demount due to strong residual magnetism. In these cases, Model EP-D (P. 34) is recommended. ■A guide for selection...

MPdeiEPBOD DEMAGNETIZING FUNCTION-EQUIPPED PERMANENT ELECTROMAGNETIC CHUCK FOR CUTTING ELECTROMAGNETIC CHUCK PERMANENT BLOCKS j VACUUM | PROMELTA* | SINE BAR j BLOCKS, HOLDERS, | HOLDING MEASURING | MAGNETIC j MAGNETIC CHUCKS CONTROLLERS i MAGNETIC CHUCKS HIJiUjWJGjMliiJ FOR MC ! CHUCKS ! SYSTEM ! CHUCKS ! MINI CHUCKS ! TOOLS TOOL HOLDERS HOLDERS ! TOOLS Weakness of checker board pattern type permanent electromagnetic chucks overcome! Bn Chuck controller required additionally EP-QD7-3469 (Mounting size equivalent to 400 x...

EP-QD / EP-QL / EP-QZ/ EP-D QZ SUPER POWERFUL PERMANENT ELECTROMAGNETIC CHUCK FOR LONG WORKPIECE [Features] •The gap characteristic is superior to that of the current Model EP-QN/ QS. These chucks are suitable for workpieces that have poor flatness and require large holding power. •These chucks replace conventional hydraulic and mechanical clamping to reduce the setup time and improve productivity. •The magnetic poles are arranged according to shapes and length of workpieces such as rails. Securing blocks specially designed according to workpiece shapes are also available. •A type with a...

Model EP-DV POWERFUL PERMANENT ELECTROMAGNETIC CHUCK WITH VACUUM FUNCTION ELECTROMAGNETIC CHUCK PERMANENT BLOCKS j VACUUM | PROMELTA* | SINE BAR j BLOCKS, HOLDERS, | HOLDING MEASURING | MAGNETIC j MAGNETICCHUCKS CONTROLLERS i MAGNETIC CHUCKS HIJiUjWJGjMliiJ FOR MC ! CHUCKS ! SYSTEM ! CHUCKS ! MINI CHUCKS ! TOOLS TOOL HOLDERS HOLDERS ! TOOLS Hybrid chuck to handle diversified materials! [Application] Permanent electromagnetic chucks for cutting equipped with a grid-seal type vacuum chuck Chuck controller and vacuum system...

EP-DV / EP-DWM / EPS-D / EPT / EPT-LW / EPT-H Power saving Minimal heat generation ［Application］ Chuck controller required additionally Suitable for high precision grinding and slicing. ●Since electricity is supplied momentarily only to control the magnetomotive force when mounting/demounting a workpiece, little heat is generated internally to enable highly precise machining. ●Since electricity needs not be supplied continuously even while holding a workpiece, the running cost is very low. ●Since the holding power is maintained by the permanent magnet, safety is secured in the event of...

PERMANENT ELECTROMAGNETIC CHUCKS Model EPTW PERMANENT ELECTROMAGNETIC MICROPITCH CHUCK Minimal heat generation Back stopper Side stopper ELECTROMAGNETIC CHUCK PERMANENT PERMANENT PERMANENT CHUCKS CONTROLLERS MAGNETIC CHUCKS ELECTROMAGNETIC CHUCKS ELECTROMAGNETIC CHUCKS Power saving Chuck controller required additionally Work Face Nominal Size Pole Pitch ［Application］ Suitable for precision grinding on grinders and for holding thin and thick workpieces having a large area. ［Features］ ●Thanks to finer pole pitches on the chuck work face, these chucks hold thin and wide workpieces firmly. ●Since...