MAGNETIZERS AND DEMAGNETIZERS
7Pages

{{requestButtons}}

Catalog excerpts

MAGNETIZERS AND DEMAGNETIZERS - 1

MAGNETIC FIELD GENERATOR For measuring management of magnetic flux density TESLA METER magnetic field strength See Page N4 for details. magnetic field strength See Page 156 for details. REFERENCE MAGNETIC FIELD MAGNETIC POLARITY CHECKER magnetic field strength See Page 156 for details.

Open the catalog to page 1
MAGNETIZERS AND DEMAGNETIZERS - 2

■How to Demagnetize and Precautions for Use •Move a workpiece over the demagnetizing surface slowly in the direction of A-B. Note that the workpiece must be moved more than 20 cm away from the end of the demagnetizer to be demagnetized •When the tunnel type demagnetizer is used, pass the workpiece through the tunneled hole. •A recommended time for passing the workpiece is about 5 seconds. (Recommended speed from 3 to 5 m/min.) •Some demagnetizers may be heated to considerably high temperature due to electromagnetic induction action, but this does not affect the demagnetizing operation at...

Open the catalog to page 2
MAGNETIZERS AND DEMAGNETIZERS - 3

Model KMDY TABLE TYPE DEMAGNETIZER Demagnetization has been improved by implement of stronger magnetic field. Designed for removing or reducing residual magnetism by passing affected work pieces over the demagnetizing face. •Use of a new 3-phase AC power design results in a more powerful magnetizing field to effectively demagnetize difficult work material and work shapes. •Effective demagnetization of work such as ring shapes such as assembled bearing gears. (Demagnetizing direction) •Improved heat dissipation making continuous use possible. [mm(in)]

Open the catalog to page 3
MAGNETIZERS AND DEMAGNETIZERS - 4

Model KMDE STATIC TYPE DEMAGNETIZER

Open the catalog to page 4
MAGNETIZERS AND DEMAGNETIZERS - 5

KMDE / KMDE-MP / KMDE-V / KMDV/ KMDU Model KMDE-V STATIC TYPE V SHAPED DEMAGNETIZER_ Static fixed position work piece demagnetization, no turning or passing! Well suited for demagnetization of ring shape work pieces. •Demagnetizes work in a one time operation. Re-positioning of work is not necessary, reducing risk of damage to part handling. •Protective plating is provided on the demagnetizing V-Faces, preventing damage to work surfaces. Re-positioning of the protection plating allows for support of uneven shaped parts. •Separate power control and KMDE-V can be located separately for...

Open the catalog to page 5
MAGNETIZERS AND DEMAGNETIZERS - 6

Model KMDT TUNNEL TYPE DEMAGNETIZER These demagnetizers can meet such demagnetizing needs as passing a bucket containing a large number of small workpieces and being incorporated in a line for continuous demagnetizing by conveyor transportation. Various sizes are available to meet such requirements. They can also be used to demagnetize long workpieces and irregularly shaped workpieces. •The good heat radiation design enables continuous operation. •A uniform demagnetizing area can be obtained. •Almost uniform demagnetization can act on the whole periphery of passing workpieces. Tunnel type...

Open the catalog to page 6
MAGNETIZERS AND DEMAGNETIZERS - 7

KMDT / KMDTR / KMDTC / KMDP / KMDH / KMDC Model KMDP Recommended where magnetism on the surface of metallic workpieces in general need to be reduced in a limited area or locally. This is useful to completely eliminate weak magnetism that remains locally in jigs and workpieces after they have been demagnetized by a large demagnetizer. It is also suitable for demagnetizing cutters of machines and punches and guide pins of press dies while they are mounted. •A rare earth magnet having strong magnetic force is used at the end of the rotary magnetic field. •Re-chargeable battery operation. Power...

Open the catalog to page 7

All Kanetec catalogs and technical brochures

  1. Model EP-QZ

    1 Pages

  2. Model KCC-AR

    1 Pages

  3. KET-U

    1 Pages

  4. Model KET

    1 Pages

  5. Model KESL

    1 Pages

  6. LIFTING MAGNET

    14 Pages

  7. MAGBORE

    2 Pages

Archived catalogs