[Application] Suitable for mating and keeping jointing parts of iron plates or members during welding work. [Features] A powerful holding type by use of a high-performance permanent magnet. MT-A-2 •Both inside and outside welding are possible. <Note 1> •Any desired holding angle can be set in a range of 45° and 135° (angle scale provided). •ON/OFF function and V-groove provided. MT-A-4 •Any desired holding angle can be set in a range of 30° and 90° (angle scale provided). •Angle adjustment with a handle. •ON-OFF function provided. (Note 1 > (Inside welding) (Outside welding) [Application] Suitable as a holding tool for welding on such work sites of construction, bridge, ship building and piping. [Features] •The magnet part has a minimum necessary free rotating angle range for easy mounting on workpieces. •The exterior of the magnet holder part is made of aluminum to prevent adhesion of iron powder on the top and side faces. •Model WK-T3A has a construction that is highly resistant to heat. • These clampers have a large mechanical strength to withstand rough handling. The holding power is based on a test piece of SS400, 10 mm thick, ground surface. MAGNETIC HOLDER Holding Power Application] Suitable for temporary holding during drilling and assembly. Features] •Two magnets combined for easy angle setting. •An angle scale provided. (KM-12W) •The magnetic force can be turned on and off by operating the lever. (KM-12W) •The V-groove allows the holder to be attached to certain poles and curved surfaces in addition to the flat surface. (KM-12W) [mm(in)] ^The holding power is per holder on one side and based on a test piece of SS400, 10 mm thick, ground surface. Precautions for use These holders cannot be used for work where heat is applied for long hours. If the magnet is subjected to high temperature, its magnetic force will drop or be lost suddenly, causing the workpiece to come off the attractive face. Exercise caution.

MAGNETIC TOOLS & EQUIPMENT FOR WELDING OPERATION Model KM-SA HEXAGONAL MAGNETIC HOLDER MAGNETIC TOOLS & EQUIPMENT MAGNETIC TOOLS & EQUIPMENT FOR WELDING OPERATION FOR WELDING OPERATION LIFTING MAGNET ［Application］ These holders provide strong holding power for temporary holding during welding and temporary assembly. These holders can also be used as a block. ［Features］ ●The holding angle can be set to 45° 90° , and 135° . ●The small type is equipped with a pushbutton and the large type with a rotary handle for turning on and off the magnetic force. ●The V-groove provided makes this holder to generate...

KM-SA / KM-S / KM-TH / KM-TA SIMPLE HEXAGONAL HOLDER [Application] These holders are used for tack welding and temporary assembly during welding and assembly work. They can be used in wide applications as they hold round pipes and round steel bars. [Features] •The holding angle can be set to 45°, 90° and 135°. •Compact and handy. Lower cost and simpler than the hexagonal holder KM-S. •The concave attractive face can hold certain round steel bars. Holding Power Holding Power Steel plate Steel plate ^The holding power on steel plate is based on a test piece of SS400, 10 mm thick, ground surface....

Model GS GUIDE SCALE > m od zz mo [Application] Special guide tools for moving a torch while maintaining the height of the nozzle during gas welding. [Features] •A high-performance permanent magnet holds the scale firmly. •Model GS-1 allows scale up-down adjustment according to the height of the nozzle. •Model GS-2 allows its magnetic force to be turned on and off with a lever for easy mounting and demounting. These holders cannot be used for work where heat is applied for long hours. If the magnet is subjected to high temperature, its magnetic force will drop or be lost suddenly, causing the...

WELDING JIG FOR ONE FACE WELDING Rectifier required additionally [Application] Jigs developed for automatic welding of steel plates to hold steel plates and backing materials. These jigs can be used to hold cut-out pieces during EPM welding operations, to straighten workpieces and to secure stacked steel plates during fusing of stacked steel plates. [Features] •Holding and releasing workpieces can be controlled electrically. •Workpieces are secured to a welding frame by a strong magnetic force and therefore warping of steel plates due to welding heat can be prevented. •Drip-proof construction...