Website:
KALEJA GmbH
Catalog excerpts
Industrial motor controller for brushed DC motors 24 VDC Design for output currents up to 8 A Control with the following functions: - reversal of direction of rotation - overload shut-down - short circuit detection - dynamic brake To snap onto the DIN rail EN 50022 Unit width: 22,5 mm 09.01.2020 KL - Errors and technical modification subject to change. All rights reserved. KALEJA GmbH Strubelweg 14 D-73553 Alfdorf Tel.: +49 7172 93711 0 info@kaleia.com
Open the catalog to page 1
Housing, terminal, printed circuit board _UL94-HB The module MAXI-MW-8-30 is a two-quadrant DC motor control for use in an industrial environment. It guarantees the switching on and off of motors. The motor stops always with dynamic braking. 09.01.2020 KL - Errors and technical modification subject to change. All rights reserved. © KALEJA GmbH
Open the catalog to page 2
| Overload/over temperature switch off | Continuous load current / total current When operating one motor, the continuous load current specified in the technical data applies. When operating 2 motors the total current depends on various factors that must be determined depending on the application. E.g.: ambient temperature, duty cycle, installation situation. The maximum specified total current must not be exceeded. The device has an integrated overload and over temperature detection. If an event occurs, the motor will be switched off. After cooling down of the device the motor restarts...
Open the catalog to page 3
Datasheet MAXI-MW-8-30 06.04.202 Safety notes Maximum operational data The maximum operating data may not be exceeded. Installation The installation and start-up must be performed by specialist personnel exclusively. All affected components must be disconnected from the mains. Start-up For the first start-up, the motor should be operated without load. Risk of death Do not touch live parts after switching on! The assembly must be operated exclusively on safety extra-low voltage. With operation on extra-low voltage (e.g. via autotransformer), death or injury can occur. Fire protection The...
Open the catalog to page 4All KALEJA GmbH catalogs and technical brochures
-
M5-2QB-12-48 06.38.0079 Pages
-
M5-BL-12-48 06.38.0019 Pages
-
M-MWS-6-301 Pages
-
M-MRI-3-302 Pages
-
M-BL-5-302 Pages
-
M-MZ-4-302 Pages
-
Maxi-1Q-4-302 Pages
-
M-1Q-6-302 Pages
-
M-4Q-6-302 Pages
-
M-2Q-6-302 Pages
-
MAXI-GMF-8-304 Pages
-
M-S-6-302 Pages
-
Maxi-S-4-302 Pages
-
MAXI-MW-8-304 Pages
-
M2-CMR-5-30 06.34.0186 Pages
-
Mini-SO-50-301 Pages
-
Mini-OM-50-301 Pages
-
Mini-OM-08-301 Pages
-
M2-MR-5-306 Pages
-
02.01.115_Mini-OM-25-301 Pages
-
06.04.201_Maxi-M-8-304 Pages
-
M2-3DR-5-308 Pages
-
M2-MWS-6-307 Pages
-
M2-MWI-6-307 Pages
-
M3-2QB-5-127 Pages
-
M3-4Q-5-307 Pages
-
Maxi-IMD-5-603 Pages
-
Maxi-IM-5-603 Pages
-
MB-121 Pages
-
Midi-OM-100-301 Pages
-
USV-S-9-B1 Pages
-
USV-S-25-S1 Pages
-
M3-2QB-5-307 Pages
-
M2-MWT-6-307 Pages
-
06.34.0082 Pages
-
06.04.0322 Pages
-
06.34.0067 Pages
-
06.34.0026 Pages
-
01.01.2121 Pages
-
01.01.2131 Pages
-
02.01.1041 Pages
-
02.01.1161 Pages
-
02.01.1171 Pages
-
02.01.1301 Pages
-
02.03.2261 Pages
-
02.06.2011 Pages
-
04.08.0011 Pages
-
06.04.0072 Pages
-
06.04.0082 Pages
-
06.04.0121 Pages
-
06.04.0141 Pages
-
06.04.0162 Pages
-
06.04.0192 Pages
-
06.04.0212 Pages
-
06.04.0252 Pages
-
06.04.0312 Pages
-
06.04.0392 Pages
-
06.04.0462 Pages
-
06.04.0482 Pages
-
06.04.0492 Pages
-
06.04.0512 Pages
-
06.04.0542 Pages
-
06.04.0562 Pages
-
06.04.0592 Pages
-
06.04.0662 Pages
-
06.04.0752 Pages
-
06.04.0781 Pages
-
06.04.0832 Pages
-
06.04.0852 Pages
-
06.04.0932 Pages
-
06.34.0015 Pages
-
01.01.0121 Pages
-
01.01.011E1 Pages
-
01.01.0071 Pages