*mydirectindustry

Catalogs
KALEJA GmbH
06.04.201_Maxi-M-8-30

06.04.201_Maxi-M-8-30

Product catalog summary

Overview: The MAXI-M-8-30 is an industrial motor controller designed for brushed DC motors operating at 24 VDC. It supports output currents up to 8 A and includes features such as overload shut-down, short circuit detection, and dynamic braking. The unit is designed to be mounted on a DIN rail EN 50022 with a compact width of 22.5 mm.

Specifications:

Nominal Voltage: 24.0 VDC
Supply Voltage: 10-35 VDC
Max Current: 15 A, Continuous Load Current: 8 A
Short Circuit Current Detection: 80 A
Shut-down Time After Short Circuit: 100 µs
Dimensions: 22.5 x 75 x 102 mm
Temperature Range: -20 to +50 °C
Storage Temperature: -30 to +85 °C
Humidity: Up to 95%, non-condensing

Technical Features:

Dynamic Brake: Always active, motor terminals switch to GND on stop
Galvanic Isolation: No
Installation: Any position, typically in a switch cabinet
Safety: Overload and over-temperature protection, short-circuit-proof

Safety Notes:

Installation and start-up must be performed by specialists.
Ensure all components are disconnected from the mains during installation.
Operate the motor without load during the first start-up.
Assembly must be installed in a fire-protected switch cabinet.
Use additional safety devices for cable breaks or control failures.

Maintenance: The assembly is designed to be wear-free. Ensure good ventilation and clean cooling openings regularly.

Contact Information: KALEJA GmbH, Strübelweg 14, 73553 Alfdorf, Germany. Phone: +49 7172 93711 0, Email: [email protected], Website: www.kaleja.com

Catalog excerpts

Industrial motor controller for brushed DC motors 24 VDC Design for output currents up to 8 A Control with the following functions: - overload shut-down - short circuit detection - dynamic brake To snap onto the DIN rail EN 50022 Unit width: 22,5 mm Control inputs Quiescent current Technical data: load circuit 09.01.2020 KL - Errors and technical modification subject to change. All rights reserved. KALEJA GmbH Strubelweg 14 D-73553 Alfdorf Tel.: +49 7172 93711 0 [email protected]

Open the catalog to page 1

Housing, terminal, printed circuit board _UL94-HB The module MAXI-M-8-30 is a one-quadrant DC motor control for use in an industrial environment. It guarantees the switching on and off of motors. The motor stops always with dynamic braking. | Typical applications: "" 09.01.2020 KL - Errors and technical modification subject to change. All rights reserved. © KALEJA GmbH

Open the catalog to page 2

| Overload/over temperature switch off | Continuous load current / total current When operating one motor, the continuous load current specified in the technical data applies. When operating 2 motors the total current depends on various factors that must be determined depending on the application. E.g.: ambient temperature, duty cycle, installation situation. The maximum specified total current must not be exceeded. The device has an integrated overload and over temperature detection. If an event occurs, the motor will be switched off. After cooling down of the device the motor restarts automatically....

Open the catalog to page 3

Datasheet MAXI-M-8-30 06.04.201 Safety notes Maximum operational data The maximum operating data may not be exceeded. Installation The installation and start-up must be performed by specialist personnel exclusively. All affected components must be disconnected from the mains. Start-up For the first start-up, the motor should be operated without load. Risk of death Do not touch live parts after switching on! The assembly must be operated exclusively on safety extra-low voltage. With operation on extra-low voltage (e.g. via autotransformer), death or injury can occur. Fire protection The assembly...

Open the catalog to page 4

06.04.201_Maxi-M-8-30

06.04.201_Maxi-M-8-30

Catalog excerpts

All KALEJA GmbH catalogs and technical brochures