This manual is designed for study the main technical characteristics, operating principle and rules of technical operation of melter 5 kg. Before use carefully read the instructions below! Improper use of the equipment can be a source of danger. By starting work with the device you confirm that you are fully acquainted with this manual and understood the rules of operation of the device. KADZAMA appreciates your purchase and wishes you a pleasant work experience.

Melter 5 kg is designed for heating and tempering chocolate.

4.1. Melter 5 kg is an electric appliance with a certain danger potential. When connecting the device to the electric grid, take all necessary precautions to avoid electric shock. 4.2. Melter 5 kg must be connected to the power supply and operated only by trained personnel. 4.3. It is not allowed to operate the melter 5 kg in the absence of electrical grounding («E» wire). 4.4. Melter 5 kg should be used only for its intended purpose. 4.5. Use and store the melter 5 kg in a place out of reach of children 4.6. Do not leave the melter 5 kg switched on without supervision for a long time. 4.7. Do...

4.12. Repair or disassembly of the melter 5 kg may only be provided with the assistance of qualified personnel of KADZAMA. 5.2. Set the melter 5 kg on a flat hard surface, providing easy access to controls. 5.3. If the melter 5 kg was at sub zero temperatures for a long time, allow it to warm up to room temperature before turning it on. 5.4. Empty the container and load at least 3 kg of chocolate into it. 5.5. Make sure that the power supply is correct and that the power source is properly grounded. Plug the equipment into a 220V.

2 — Temperature display: it shows the current temperature value as well as the set temperature value if any button is pressed; 3 — Temperature deviation indicator (▲ I B I ▼). Indicator (▼) signals that the current temperature is less than the set one. Indicator (▲) signals that the current temperature exceeds the set one. Indicator (B) signals that the current temperature matches to the set one; 4 — Temperature set value indicator (SV). To check or change the current temperature set value (SV), press any key on the front panel once, while the set value indicator (SV) is on and the set value...

IMPORTANT! For correct equipment operation it is necessary to maintain a room temperature from 18°C to 25°C. Otherwise, the heating system will show a result higher, than the permissible one (we also draw your attention to the fact that deviation from temperature standards in the room can affect the quality of the product, since in most cases its properties also depend on the environment). 7.1. Turn on the melter with the ON / OFF button. The controller display must light up. 7.2. Temper the chocolate. There are many methods of tempering the chocolate with a steam table. The easiest tempering...

— Mix well until the pieces are completely dissolved. The pieces should melt completely at the moment the set working temperature is reached; IMPORTANT! If the pieces are dissolved at a temperature of 34°C and above, then there is a big chance that the chocolate won’t contain the required quantity of stable crystals. If the set temperature is reached, and the pieces are not melted, then cover the container with a lid and repeat stirring after 10-15 minutes until the pieces are completely dissolved. — Collect the probe and check the quality of the tempering; — Upon finishing the work, set the...

mass should change its gloss to matte, the chocolate becomes much thicker. — Collect the chocolate in a cup and return it to the tempering container. Mix thoroughly. The temperature of the chocolate mass must be within the working temperature range of the chocolate; — Collect the probe and check the quality of the tempering; — Upon finishing the work, set the temperature to 40°C, cover with a lid; — To start the work, repeat all the steps again. — For a quick start the chocolate in the container must be already tempered. This technique is suitable if you plan to continue working in the near future...

— Upon finishing the work, set the temperature to 36-37ºC (depending on the room temperature). 7.3. Recrystallization of chocolate. Recrystallization of chocolate is a process in which a mass of chocolate, being at the same temperature (for example, 33ºC), changes its viscosity to a more viscous one. After 1-2 hours of working with the prepared chocolate, the recrystallization process begins (appears as increased viscosity of the product). In order to return the chocolate to its normal state, it’s enough to evenly heat it with a heat gun to a temperature of 33.5-34ºC (or add hot chocolate with...

8.1. Malfunctions checklist for melter. If your melter does not start, follow these steps: — Check the power supply cable, it must be undamaged and connected to the equipment correctly; — The socket where the equipment is connected has a right voltage for the power supply parameters specified in the technical characteristics of the connected equipment (Your building may be completely de-energized, or the circuit breaker responsible for this socket is turned off in the junction box of the room); — The equipment plug is connected to the socket correctly and completely; — Switch on the equipment,...

— If the bowl still continues to heat up or there are other deviations after reaching the set temperature, it’s recommended to do the initial setting of the controller; — If all of the above conditions are met, and the equipment cannot be restored to work, please inform the KADZAMA manager about all the steps you have done for further consultation. Initial parameter setting: First you must unlock the settings, to do this use the relevant section below. Then turn on the device, press the MODE button on the controller and hold it until the PAr2 parameter appears on the screen, release the button....