Juststream
8Pages

JETSTREAM™ & JETSTREAM™ GV-X EN12941 : 1998 RESPIRATORY PROTECTIVE DEVICE POWERED FILTERING DEVICE, INCORPORATING A HELMET OR HOOD, USER INSTRUCTION MANUAL IMPORTANT - This manual must be read and fully understood before the Jetstream is used. This manual must be retained for future reference.

Important - Please read these instructions carefully before unpacking your Jetstream product. Failure to comply with the instructions in this leaflet may void your warranty and adversely affect your health. If you have any questions regarding the suitability of this product to your task, please contact an occupational hygienist or call the manufacturers technical help line. Address and Telephone number information is printed at the back of this leaflet. Unpacking - Your Jetstream Powered Respirator should include: a) Blower Unit b) Belt c) Head Cape with Hose d) Airflow Test Unit e) Battery...

System Overview - Jetstream GV-X Jetstream GV-X is a belt mounted powered respirator with a range of filters for protection against Particles and/or Organic gases and vapours with boiling points above 65°C. Jetstream GV-X contains an 8hr rechargeable battery pack. Jetstream GV-X will warn the user when the MMDF of 140 L/min, is reached. The Jetstream GV-X range of Filters have been developed especially for this unit. They are used to filter the air the user will breath. The Jetstream GV-X Filters are intended to be disposed of once clogged to the point of triggering the warning signal. A...

Waist-Belt Adjustment Put the belt around your waist and fasten the two ends together; If the belt is too loose, slide the male adjuster down the belt, towards the female half. If the belt is too tight, slide the male adjuster away from the female half. Repeat the above processes until a comfortable and secure fit is achieved. (See Diagram 1) Once the belt fits correctly, secure any excess belt material using the Velcro sections. Diagram 1: Filter Selection Use only “Jetstream and Jetstream GV-X” Filters manufactured by JSP Ltd. (See Diagram 2). It should first be ascertained by consulting...

Spark Guard The Spark Guard is included with the Jetstream TH2P filter (not suitable for fitting to the Jetstream TH2A2 or TH2A2P filters or other types of JSP filters). The Spark Guard is a simple push fit. Line up the finger recess on the Spark Guard with the finger recess on the filter housing (see diagram 9, 10 and 11) and push into place. Ensure a positive click fit is heard. Diagram 9: FINGER RECESS FINGER RECESS Diagram 12: When the Jetstream TH2P filter is exhausted simply pull off the Spark Guard. Under normal circumstances the Spark Guard can be used up to 5 times. The Spark Guard...

Attaching the Hose to the Blower Unit Switch on the blower unit and allow it to stabilise, the warning buzzer will stop when the unit is stabilised. If the buzzer fails to stop either the filter requires replacement or the battery needs recharging. Once the buzzer has stopped attach the hose. Place the Bayonet connector (See Diagram 16) over the ‘Chimney’ of the Jetstream, push down and twist in an anti-clockwise direction (See Diagram 17.) until the locating pin clips into place. (See Diagram 18.) Diagram 16: BAYONET FITTING TWIST BLOWER CHIMNEY NOTE: The hose is permanently attached to...

Donning the Welding Visor Lift the hose coupling over the top of the inner harness and unscrew the red ratchet wheel to it’s maximum size (see Diagram 26). Place the inner harness over the head with the chin hooked inside the front part of the inner hood and re-tighten the red ratchet wheel until a secure but comfortable fit is achieved (see Diagram 27). Pull the hose coupling back down over the inner harness and allow the elastic at the rear to seal the inner hood on to the head (see Diagram 28). Diagram 26: PULL HOSE COUPLING OVER RATCHET WHEEL WHEEL RATCHET Donning the Browguard Open the...

Storage and Transportation When not in use or during transportation the blower and head units should be stored in the container in which they were provided, or other similar container, such that it is out of direct sunlight, not in contact with solvents and cannot be damaged by physical contact with hard surfaces/items. Do not store outside the temperature range of +2°C to +55°C or with humidity above 75%RH. Charging the Battery Once the unit has reached it’s MMDF, it is best to leave it to run down completely before recharging. Plug the Charger into the mains Socket, fit the Plug on the...