video corpo

CPKT
1Pages

{{requestButtons}}

Catalog excerpts

CPKT - 1

C SERIES VERTICAL RIGID COUPLINGS InstaUation Instructions Installation 1. Align equipment to pump manufacturer's specification. Ensure shaft runouts are within specification. 2. Slide motor hub onto motor shaft until circular keyway on shaft is exposed. Holding hub in this position, install the axial key and split circular key halves. Slide the motor hub down until it stops against circular keys (Figure 1). 3. Slide pump hub onto pump shaft and install axial key. 4. Thread adjusting nut assembly into the pump shaft (75% minimum thread engagement recommended). NOTE: It may be necessary to install the long bolts in the pump hub prior to fitting on the shaft if the first obstruction is too close. 5. Install spacer ensuring pilot fits into the adjusting nut assembly. 6. Determine the distance impeller must be raised as specified by the pump vendor. 7. Turn adjusting nut until distance 'A' is equal to distance from Step 6 (Figure 1). Turn adjusting nut downward onto shaft to align bolt holes with pump hub. 8. Insert long bolts and fit nuts in rotation until coupling is drawn together securely. Tighten nuts to values shown in Table 1. All rotating power transmission products are potentially dangerous. They should be used according to the manufacturer’s recommendations and appropriate safety standards. It is the responsibility of the user to comply with any such standards. iohn crane Asia Pacific Singapore Tel: 65-6518-1800 Fax: 65-6518-1803 North America United States of America Tel: 1-847-967-2400 Fax: 1-847-967-3915 Europe United Kingdom Tel: 44-1753-224000 Fax: 44-1753-224224 Latin America Brazil Tel: 55-11-3371-2500 Fax: 55-11-3371-2599 Middle East & Africa United Arab Emirates Tel: 971-481-27800 Fax: 971-488-62830 smiths bringing technology to life If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. ISO 9001 and ISO14001 Certified, details available on request. ©2017 John Crane Revised 10/17 www.johncrane.com

Open the catalog to page 1

All John Crane catalogs and technical brochures

  1. Type 28VL

    4 Pages

  2. Type 28VL

    4 Pages

  3. Type 93FR

    4 Pages

  4. Type 28AT

    8 Pages

  5. TYPE 8648VRS

    2 Pages

  6. AURA™

    2 Pages

  7. H-RE

    12 Pages

  8. H-CE

    12 Pages

  9. A series

    8 Pages

  10. TYPE 2800MB

    8 Pages

  11. TYPE 2715T

    8 Pages

  12. TYPE 1670

    4 Pages

  13. G58/G58I

    2 Pages

  14. CVU/CVH

    2 Pages

  15. CPR BUSHING

    4 Pages

  16. TYPE EZ-1®

    8 Pages

  17. GR-2/2C

    2 Pages

  18. GR-1/1C

    2 Pages

  19. LIVE-LOAD

    2 Pages

  20. 1345/1349

    2 Pages

  21. 387I

    2 Pages

  22. TYPE 502

    6 Pages

  23. TYPE 2106

    4 Pages

  24. TYPE 676

    8 Pages

  25. TYPE 2100

    4 Pages

  26. TYPE 21

    6 Pages

  27. TYPE 1/1B

    6 Pages

  28. GR2/2C

    2 Pages

  29. GR1/1C

    2 Pages

  30. GP-S/GP-D

    2 Pages

  31. Type 93FR

    4 Pages

  32. Type 83

    4 Pages

  33. Type 28XP

    6 Pages

  34. Type 28VL

    4 Pages

  35. Type 28ST

    4 Pages

  36. Type 28AT

    6 Pages

  37. CK736/736D

    4 Pages

  38. SEW Ahlstar

    4 Pages

Archived catalogs