Jinan USR IOT Technology Limited

Features 10 / 100Mbps adaptive Ethernet interface, support AUTO-MDIX network cable crossover and direct  connection automatic switching. Work modes:TCP server, TCP client, UDP server, UDP client.  Baud rate can be set from 600bps to 230.4Kbps. Parity supports None, Odd, Eben, Mark, Space.  Customize heartbeat package and keep the connection real and reliable, can be used to detect the  dead connections Customize registration package, detect the connection status, and also customize the head of package.  In TCP Server mode, the number of connected clients can be modify from 1 to 4, default...

technical support:h.usriot.com

technical support:h.usriot.com Jinan USR IOT Technology Limited

technical support:h.usriot.com 1. Get start 1.1.Quick Test 1. USR - K5 2. USR - Kx - EVK 3. One Internet cable 4. One power supply of DC5V 1A 5. Serial line 6. One PC Hardware connection To test a serial port to network communication conversion, we will K5 (USR - K5, referred to as "K5, similarly hereinafter) serial port via a serial port line (or turn the USB serial port) connected to the computer, the K5 with cable front-end ports and connected to the front-end ports of the PC, hardware connection without error, access our distribution power adapter, to power a K5, connection diagram as shown:...

technical support:h.usriot.com 3) for the case where the server is directly connected to PC, a static IP address in the same network segment as K5 IP must be set for the computer; Computer settings You can set up the parameters as the follows default parameters through M0 set-up software or inner website. You can check the details at chapter 3. Default parameter User name Password IP Subnet mask Work mode Work mode Local port Remote port Default remote port Serial-port baud rate Jinan USR IOT Technology Limited

Jinan USR IOT Technology Limited technical support:h.usriot.com Software settings

technical support:h.usriot.com Data transmission test After the above steps are confirmed to be correct, the two-way communication between the serial port and the Ethernet port can be carried out. The operation steps are as follows: 1) open the Test software usr-tcp232-test.exe, and connect the hardware according to figure 1.2. 2) select TCP Server mode in the network setting area, input the computer IP address of the Server, input the port number of the Server 8234, click to start listening, establish the TCP connection, set the baud rate of the serial port to 115200, set the serial port parameter...

technical support:h.usriot.com 1.2.Basic Parameters USR-K5 is a tiny size serial port to Ethernet module which can realize the bi-direct data transparent transmission between RJ45 port and TTL serial port. It can be applied to RS232 and RS485 by level conversion circuit. Supports low power consumption, only consume a little current in full speed work. Equipped with Cortex-M0 core, fast speed and high efficiency. Supports several functions to meet more needs. K5 is easy to operate and have strong compatibility. On the basis of adding new functions, it is compatible with the setting protocol of...

operating humidity technical support:h.usriot.com Electrostatic bubble Storage humidity 1.3.Product Function Here are the functions of K5, below is the overall block diagram. Jinan USR IOT Technology Limited

technical support:h.usriot.com 1.4.IP Mode IP address/ Mask/ Gateway 1. IP address is the identity representation of the module in the LAN, which is unique in the LAN, so please be sure there is no another device same as it in the LAN. The static IP needs to be manually set by the user. During the setting process, pay attention to write the IP, mask, and gateway at the same time. The static IP is suitable for scenarios where IP and equipment need to be counted and one-to-one correspondence is required. Pay attention to the corr/espondence between IP address, mask and gateway when setting. When...

technical support:h.usriot.com Software Setting You can easily install and configure your device server over the network In this section, we will cover only the “configuration of general settings” using N510 Administrator. For more detailed information on how to use this suite of useful utilities, refer to Chapter 3 and 5. 1.5.1. Installing M0 Set-up software Download and run (https://www.usriot.com/support/downloads/usr-m4-setup-software-v235102.html ). You may find it in the Resource section under your product page. 1.5.2. Searching for Device Servers over a LAN The Broadcast Search function...

technical support:h.usriot.com In M0 software, click Search to search your LAN for device servers. When your unit appears in the search results,You may also wait a few more moments for the search to complete. Figure 8 Search device Right-click your unit in the Configuration screen and select Configure in the menu.The device server must be assigned a unique IP address that is valid for your network. Both static and dynamic IP addresses are supported. The ip type you can check the details refer to Chapters 2 for a detailed explanation of different operating Consult with your network administrator...

technical support:h.usriot.com 1.6.Configuration by web console 1.6.1. Connect with Network Connect one end of the Ethernet cable to the 10/100M Ethernet port and the other end of the cable to the Network .The device will indicate a valid connection to the Ethernet in the following ways: Open your browser User can connect PC to N510 through LAN port and enter Web Server to configure. Web Server default parameters as follow: Diagram 2 Parameter Web server IP address User name Password Jinan USR IOT Technology Limited Default settings Web server default parameters

technical support:h.usriot.com After firstly connecting PC to K5, user can open browser and enter default IP 192.168.0.7 into address bar, then log in user name and password, user will enter Web site: K5 is same as the normal web page server, which is convenient for user to setting parameter and query the status. The port of web page can be setting, default is 80. Steps:  Open the browser, fill the IP of K5, e.g.:192.168.0.7(IP address and PC in the same net segment.)  Fill the user name and key word in the login web page, default is admin, click to enter. TX Count: the data count sent from...