Application field - Medical Line &Care Line preferably in medical equipment and rehabilitation JCB35Q has a compact and elegant design, it is widely used to demanding medical or rehab equipment where space is important. And JCB35Q are available for 2 installation ways: with several actuators via special mounting bracket or to frame via screws. Exchangeable power cables, Electronic overload protection, SMPS (switching mode power supply)power supply, optional power make JCB35Q a good choice for worldwide usages. General Features Power SMPS Power Power Indicator Actuator Port Hand Control Port Battery Port Standby Power Consumption Colour Control Concept Duty Cycle Input 100-240VAC, 50/60 Hz 50W / 100W Yes Max. 4 channels, 4 or 5 Pin Din connector 1 channels, 8 Pin Din connector 1 channel, 6 Pin Din connector (output 30uA - actuator does not work) Maximum 1W (230V) Black/Gray Relay, the service life exceeds 20000 cycles 10%, max. continuous work for 2min. and 18 min. off Weight Actuator Compatibility Battery Management General actuators or columns with limit switch The power supply of the battery can be cut off at low voltage, and there is charge and discharge management inside the battery Protection Class Safety Protection Installation Pull-out Protection Approval Max. IPX6 SMPS overheat protection / Over-current protection With actuators via special mounting brackets; bed frame via screws Yes IEC 60950-1/KC60950-1 KN32 KN35 IEC/EN60601-1-2 ANSI/AAMI ES60601-1 CSA CAN/CSA-C22.2 NO. 60601-1:14

O JIECANGUsage Operating Temperature: +5 °C to +40oC Relative Humidity: 20% - 90% under 30°C , non condensing

O JIECANG Installation type Ordering KeyTake JCB35Q043GQ0046100030 as an example Model

O JIECANGDiagram-system overview Installation Mounting bracket

Dimensions of JCB35Q with linear actuators JCB35Q (general type) installing with actuator JC35L3 JCB35Q (installation type) installing with actuator JC35L3

JCB35Q (general type) installing with actuator JC35L9 JCB35Q (installation type) installing with actuator JC35L9

Installing JCB35Q (installation type) to the frame Cable exit (cable locker can be removed) It is recommended to install the JCB35Q where the water can be drained. Suggested screw installation torque: 0.6Nm +/-0.1 JCB35Q can be installed to the bed frame or any other applications according to one of the following installation instructions: 1) M5 screw+ M5 screw nut. Place M5 screw nut on the screw holes on the slide-on bracket, and fix it with M5 screws. 2) Fix the slide-on bracket with M5 screws + flat washer+ screw nut. 3) Fix the slide-on bracket to the frame with tapping screws.

O JIECANGPull-out Protection and Cable ManagementLinear actuator cable locking 1. JCB35Q has a uniquely designed cable cover. When it is equipped, it acts as an integrated actuator cable lock. 2. Equipping the cable cover until it snaps into place.(please refer to the below illustration) LED indication JCB35Q has a green LED power indicator. When JCB35Q is successfully connected to the power, the LED indicator is on.

O JIECANGStrictly abiding by medical safety certifications Passed EMC tests. To ensure our products pass all kinds of tests domestic or abroad. Communication protocol development Aiming at different applications, develop more extensive functions for control system. Professional customization Powerful R&D strength, fully satisfy customers’ needs. Development cycle is about 10 days, seizing more market opportunities Intelligent Control of Bluetooth Mobile phone as the remote, applying in home care. Market pioneer, Jiecang provides better choices Controllers adopt high-frequency wireless system....