Catalog excerpts
Quality products for Mechanical! & Fluid Power
Open the catalog to page 1‘QM’ Quick Maintenance Flange Seal
Open the catalog to page 2Contents quality products for mechanical & fuid power Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Pressure Welding Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Pressure Blanking Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Pressure Flange & Welding...
Open the catalog to page 3‘QM’ Quick Maintenance Flange Seal Replaceable Seal System Important Characteristics jbj Techniques Limited produce and supply an innovative range of pipe flanges for fluid systems. Designed for pressures up to 450 bar, flow rates up to 20,000 l.p.m. and pipe sizes between 20 and 220 mm outside diameter. They are specifically aimed at the steel, oil, gas and food industries where ease of maintenance features are economically attractive. Seal replacement downtime has been found to be reduced by more than 400%. The ease of maintenance feature involves the ability to remove the seal, which is...
Open the catalog to page 4‘QM’ Quick Maintenance Flange Seal High Pressure Welding Nipple Plastic Seal Type. Maximum pressure 450 Bar ØG Refers to maximum allowable hole in mating part ordering code: to suit pipe wall
Open the catalog to page 5Plastic Seal Type. Coupling assembly 450 bar. 450 bar ordering code: ST 52.3 1.4404 QM...CC***-- QMx...CC***-- where *** = tube diameter -- = wall thickness Repeat if tube detail differs per side
Open the catalog to page 6Plastic Seal Type. Maximum pressure 450 bar. 450 bar QM...CB QMx...CB
Open the catalog to page 7‘QM’ Quick Maintenance Flange Seal High Pressure Flange & Welding Nipple Pretensioning type Plastic Seal Type. Maximum pressure 450 Bar ØG Refers to maximum allowable hole in mating part ordering code: to suit pipe wall
Open the catalog to page 8‘QM’ Quick Maintenance Flange Seal High Pressure Flange & Welding Nipple Pretensioning type Plastic Seal Type. Coupling assembly 450 Bar ØG Refers to maximum allowable hole in mating part to suit pipe wall ordering code: ∗∗∗ = tube diameter -- = wall thickness Repeat if tube detail
Open the catalog to page 9High Pressure Blanking Flange Pretensioning type Plastic Seal Type. Maximum pressure 450 bar. 0G Refers to maximum allowable hole in mating part 450 bar
Open the catalog to page 10‘QM’ Quick Maintenance Flange Seal Seal replacement downtime dramatically reduced! Ability to remove the seal and replace it without fully disconnecting or moving the mating flange or runs of pipework. jbj Techniques manufactures and markets an innovative range of pipe flanges for fluid systems, designed for: » pressures up to 450 bar. » flow rates up to 20,000 l.p.m. » pipe sizes between 20 and 220 mm od. They are specifically aimed at the steel, oil, gas, chemical, pharmaceutical, and food industries where ease of maintenance features are economically particularly attractive, when downtime...
Open the catalog to page 11jbj Techniques Limited 28 Trowers Way Holmethorpe Industrial Estate Redhill Surrey RH1 2LW. UNITED KINGDOM quality products for mechanical & fluid power jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/EC requirements set by James Harris, jbj Techniques Limited
Open the catalog to page 12All Jbj Techniques Limited catalogs and technical brochures
-
PUMP DRIVE COMPONENTS
61 Pages
-
Shaft locking devices
92 Pages
-
HIGH/LOW, 2 STAGE / GEAR PUMPS
14 Pages
-
S-Flex Couplings
32 Pages
-
Hydraulic Gear Motors
56 Pages
-
Planetary Gearboxes
48 Pages
-
Yoke Drive Flywheel Couplings
14 Pages
-
Bearing Supported Stub Shafts
12 Pages
-
This is what we do
1 Pages
-
HQ series vane pumps
48 Pages
-
Pneumatic Starters
6 Pages
-
Coolers & Heat Exchangers
78 Pages
-
Hydraulic power take-off units
28 Pages
-
Gear pump summary
12 Pages
-
FLUID POWER ACCESSORIES
66 Pages
-
F15 Ferra Series
20 Pages
-
KT Pressure Switch
8 Pages
-
Rotary Gear Flow Dividers
16 Pages
-
W Series
8 Pages
-
GPA Series
18 Pages
-
jbj Coolers Summary
2 Pages
-
An excellence in engineering
1 Pages
-
PIPE FLANGES PORT FLANGES
102 Pages
-
TANKS / RESERVOIRS
22 Pages
-
PRESSURE INTENSIFIERS
22 Pages
-
SCREW PUMPS
50 Pages
-
HAZARDOUS AREAS SCREW PUMPS
24 Pages
-
SCREW PUMP RELIEF VALVES
14 Pages
-
BV Series VANE PUMPS
94 Pages
-
BQ Series VANE PUMPS
108 Pages
-
TQ and TV Series VANE PUMPS
36 Pages
-
HQ Series VANE PUMPS
38 Pages
-
B1 and B2 Series VANE PUMPS
10 Pages
-
All steel gear couplings
26 Pages
-
This is jbj Techniques!
28 Pages
-
Vane pumps
10 Pages
-
Fluid power accessories
54 Pages
-
Fluid reservoirs
22 Pages
-
pressure intensifiers
22 Pages
-
screw pumps
50 Pages
-
API 676 compliant screw pumps
24 Pages
-
Petrol engine adaptors
6 Pages
-
Torque limiting couplings
20 Pages
-
Torsional couplings
48 Pages
-
jbj PRODUCT SUMMARY
6 Pages
-
Equipment for Hazardous Areas
44 Pages
-
PDC
58 Pages