User Manual □ GAZ 15 □ GAZ 23 Please read these instructions before operation Please save these instruction Preface Thank you for purchasing this high performance, liquid-cooled, automobile engine-driven generator. The generator set is approved for use in stationary applications in locations served by a reliable utility power source. Read this manual and carefully follow all procedures and safety precautions to ensure proper equipment operation and to avoid bodily injury. Read and follow the Safety Precautions and Instructions section at the beginning of this manual. If any portion of this manual is not understood, contact the nearest Dealer for starting, operating and servicing procedures. For professional advice on generator set power requirements and conscientious service, please contact your nearest distributor or dealer. If you have any questions or suggestions, please contact us at any time

Chapter one Technical Feature Ⅰ.Technical Feature Ⅱ. Specification Chapter two Important Safety Instruction Ⅰ. Precautions Ⅱ. Operating System Functions and Definitions III. IV. V. VI. Pre-start Preparation Startup Inspection Generator Set When Operating. Shut the generator set down Chapter Three Conservation of Engine Ⅰ. Long-term Conservation of Engine Ⅱ. The Starting After Long-term Conservation of Engine Chapter Four Check before

I. Technical Feature of the Single-Fuel Generator This gas generator is multi-fuel drive uses an optimized dedicated multi-fuel engine. According to our standards, we have designed this unit in a simple and environmentally safe, and user-friendly means: 1. Speed Regulating System: The gas uses an internally designed electronic speed control system, allowing for quick and easy adjustments to the engine speed that can be stabilized to specific speed ranges. This control system allows the engine to run more smoothly and respond quickly to sudden increases or decreases in required engine speeds....

Chapter two: Important Safety Instruction SAVE THESE INSTRUCTIONS - This manual contains important instructions for Models GAZ-23 that should be followed during installation and maintenance of the generator and batteries. I. Precautions 1. Generator set operation. Carbon monoxide can cause severe nausea, fainting, or death. Carbon monoxide is an odorless, colorless, tasteless, nonirritating gas that can cause death if inhaled for even a short time. Avoid breathing exhaust fumes when working on or near the generator set. Never operate the generator set inside a building. Never operate the generator...

Hot engine and exhaust system. Can cause severe injury or death. Do not work on the generator set until it cools 3. Servicing the exhaust system. Hot parts can cause severe injury or death. Do not touch hot engine parts. The engine and exhaust system components become extremely hot during operation. Servicing the engine heater. Hot parts can cause minor personal injury or property damage. Install the heater before connecting it to power. Operating the heater before installation can cause burns and component damage. Disconnect power to the heater and allow it to cool before servicing the heater...

4. Grounding electrical equipment Hazardous voltage can cause severe injury or death. Electrocution is possible whenever electricity is present. Ensure you comply with all applicable codes and standards. Electrically ground the generator set, transfer switch, and related equipment and electrical circuits. Turn off the main circuit breakers of all power sources before servicing the equipment. Never contact electrical leads or appliances when standing in water or on wet ground because these conditions increase the risk of electrocution. When grounding of this output AC circuit is required, use...

authorized personnel. If there is any problem of generating set, please contact retailer. Ⅱ. Operating System Functions and Definitions Depending on the generator unit model, control button functions may vary significantly. Refer to the following functions: 1. Operating System 1. Control panel 2. Power switch 3. Fuel switch 4. Stop 5. Manual 6. Start 7. Data check 8. Data check Power switch： Function：The power switch controls the entire generator set control system. If this switch is placed in the OFF (O pushed in down mode) position, the internal electrical control circuit of the unit will not...

Emergency stop switch： Function：The photo above is of the Emergency Stop Switch and is located on the front face of the generator unit. When depressed, all generator control systems will immediately shut down, including the engine and generator head. This Emergency Stop Switch should be depressed should any unexpected emergencies occur. Depressing this button can help minimize dangerous occurrences to persons, pets, property, plants, or to the generator unit itself. Use：When an emergency occurs, immediately press the Emergency Stop Switch. The unit will immediately stop running. Once the switch...

III. Prestart Preparation All necessary installation and maintenance shall be conducted by authorized personnel. Check all items in the following before running it for the first time. 1. Engine Oil. Fill, if necessary, with the recommended viscosity and grade of oil. Or it causes damage on engine. Use the following recommended or similar engine oil • Put the funnel at engine oil inlet, keep not leans • When first time operate new unit need to add 4L oil • Check the oil gauge, the oil level should keep at top center of two line 2. Coolant Only fill coolant into the radiator instead of other liquid...

Loosen cap to drain oil as well as coolant. 3. Liquid propane (LP Vapor) In engines set up to run on Liquid propane, please check the fuel supply pressure, lower or higher-pressure range will result in equipment failure. Inlet pressure 1.7kPa to 3.5kPa, and the gas pipe shall be no longer than 5m, the inner diameter shall not be less than 16mm. Pressure meter Pressure relief valve It’s strictly prohibiting to remove the high-pressure pipe when in maintenance. You must make sure there’s no leakage before use. If there is no special equipment, you can use soap bubble to test the gas pipe joints....