12210 Series
2Pages

{{requestButtons}}

Catalog excerpts

12210 Series - 1

SELF-PRIMING PUMP FEATURES Body: Jabsco Neoprene or Nitrile Compound 115 Volt AC with Replaceable Brushes, Stainless Steel Shaft, 6' cord, three prong grounding plug 3/8" Internal Pipe Thread VARIATIONS AVAILABLE MODEL NO. Neoprene Impeller Nitrile (oil resistant) Impeller INDUSTRIAL: Transferring liquids. Velocity-mixing. Pumping coolants. Pumping waste water to sewer. Cellar, yard and sump drainage. Cooling Heliarc welding equipment. MARINE: Washing down decks and docks. Water for ship's service supply. Pumping out crank-case oil. FARMING: Pumping water for stock, poultry houses, farmhouse. Pumping water from wells and cisterns. Pumping liquid ballast into tractor tires. Pumping water from flooded basements. PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, cesspools, sumps, etc. Draining water heaters and water closets. Draining laundry tubs ! Explosion hazard. Do not use where flammable vapors are present. To do so can cause an explosion resulting in injury or death. below sewer level. Removing water trapped between walls, draining inaccessible places when pipes break or leak. Draining fishing ponds and garden pools. Removing sludge, lyewater and other caustics from stopped up drains and sinks. OPERATING INSTRUCTIONS 1. INSTALLATION – Pump may be mounted at any angle without loss of efficiency. Suggested mounting is horizontal or with pump head down. The inlet port is the right hand port when looking at the end cover. 2. DRIVE – Direct. 3. SELF-PRIMING – Pump will produce a suction lift approaching 5 feet when dry and a lift up to 20 feet when primed. BE SURE SUCTION LINES ARE AIRTIGHT. 4. RUNNING DRY – Unit depends on liquid pumped for lubrication. DO NOT RUN DRY for more than 30 seconds. Lack of liquid will damage the impeller. 5. NOTICE – Do not pump solvents, thinners, highly concentrated or organic acids. If corrosive fluids must be handled consult Jabsco Chemical Resistance Table (available on request from ITT Jabsco). Pump life will be prolonged if pump is flushed with water after each use or after each work day. 6. DUTY – The “Handi-Puppy” is designed for intermittent duty in applications such as: transferring liquids; draining water heaters and water closets; pumping water from basements and other applications which require a few hours of continuous operation. 7. TEMPERATURES – Neoprene 45°F (7.2°C) to 180°F (82.2°C), Nitrile 50°F (10°C) to 180°F (82.2°C). 8. FREEZING WEATHER – Drain unit by loosening end cover plate. HEAD CAPACITY TABLE PSI

Open the catalog to page 1
12210 Series - 2

ASSEMBLY 1. Lubricate seal. Install in cavity with open side of seal facing impeller. 2. Lubricate motor shaft and install body on motor. 3. Lubricate impeller bore and aligning flat in impeller with flat on motor shaft, install impeller. 4. Install gasket, end cover and screws. FRONT VIEW OF MOTOR Screw - End Cover End Cover O-ring (end cover) Impeller - Neoprene Impeller - Nitrile Seal Slinger Screw (body to motor) Motor 12V (Facing Motor Shaft PART NUMBER Service Kit, Neoprene 90092-0007 Service Kit, Nitrile 90092-0004 Pump Head only, Neoprene 9040-1001 Pump Head only, Nitrile 9040-1003...

Open the catalog to page 2

All Jabsco catalogs and technical brochures

  1. Automotive

    12 Pages

  2. FanEx

    4 Pages

  3. AirEx

    2 Pages

  4. 18940-0010

    4 Pages

  5. 59520 series

    2 Pages

  6. 18660-0121

    4 Pages

  7. 11810 series

    4 Pages

  8. 36770 series

    2 Pages

  9. 35760 series

    4 Pages

  10. 35515-0010

    2 Pages

  11. 34739 Series

    4 Pages

  12. Model 31705

    4 Pages

  13. GEAR PUPPY

    2 Pages

  14. Searchlights

    12 Pages

  15. Toilet Systems

    18 Pages

Archived catalogs