Catalogs >
Jabsco >
Ventilation Blowers

Ventilation Blowers
8Pages

Catalog excerpts

Ventilation Blowers 09 Introduction Heavy Duty Radial Blowers Radial Blowers In-Line Blowers

09 Ventilation Blowers Product selection Heavy Duty Radial Blowers Heavy Duty Flangemount Blowers Ducting Size 24 volt DC flangemount, fuse 10 amp. 24 volt DC flangemount, fuse 10 amp. 115 volt AC 60Hz flangemount, fuse 2 amp. 12 volt DC flangemount, fuse 15 amp. 115 volt AC 60Hz flangemount, fuse 2 amp. Heavy Duty Flexmount Blowers Size (length x width x height) 12 volt DC flangemount, fuse 15 amp. Ducting Size Size (length x width x height) Radial Blowers Size (length x width x height) Voltage Output 12 volt DC flangemount, 3” (75mm) fuse 6 amp. 12 volt DC flangemount, 3” (75mm) fuse 10...

Open the catalog to page 3

Product Selection Ventilation Blowers

Open the catalog to page 4

09 Ventilation Blowers Introduction Jabsco DC blowers are designed to remove fumes from the engine compartments of gasoline powered boats prior to start-up and therefore conform to ISO 8846 MARINE and USCG Regulations for ignition protection. They are listed as N.M.M.A. type accepted and comply with ISO 9097 MARINE and are CE marked. AC models are not ignition protected. Jabsco blowers can also be used for air intake or extraction in galleys, bilges, accommodation and head compartments. Only the heavy duty blowers are designed for continuous duty operation in commercial or heavy use...

Open the catalog to page 5

Flangemount Blowers Flexmount Blowers Heavy Duty Flangemount Blowers Heavy Duty Flexmount Blowers Heavy Duty Blowers are designed for applications such as commercial or high use engine room ventilation and extraction where a long life requirement demands heavy duty motors with long brush life. Built to provide the same high outputs as our standard specification blowers. Flexmount Blowers are built to the same high specification as the Heavy Duty Flangemount Blowers for use as air intake or extraction systems in engine rooms, fuel compartments, galleys or heads. • 5,000 hr motor life for the...

Open the catalog to page 6

09 Ventilation Blowers Radial Blowers Sizing Definitions Flangemount Blowers Range of high volume air intake or extraction blowers for engine room, fuel compartment, galley or heads. • Outlet flange mounts directly on bulkhead. • Slip-on inlet ducting connection. • Low current draw. 8” long x 6¾” wide x 7¾” high (20cm x 17cm x 20cm). • Dimensionally stable quiet running Delrin rotors. • Corrosion resistant materials throughout. • Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection). 12 volt DC flangemount, fuse 10 amp. 24 volt DC flangemount, fuse 5 amp. • ISO 9097 MARINE...

Open the catalog to page 7

Flexmount Blowers Range of high volume air intake or extraction blowers for engine room, fuel compartment, galley or heads. 8¼” long x 7¾” wide x 9” high (21cm x 20cm x 23cm). • Flexmounting for 360° adjustable outlet. 115 volt AC flexmount, fuse 1.25 amp. • Slip-on inlet and outlet ducting connections. • Low current draw. • Dimensionally stable, quiet running Delrin rotors. • Corrosion resistant materials throughout. • Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection). 8” long x 8¼” wide x 9” high (20cm x 21cm x 23cm). • ISO 9097 MARINE (Electric Fans). 12 volt DC...

Open the catalog to page 8