Transfer Pumps
3Pages

ITT Marine Catalogue artwork:v21 03/11/2009 15:39 Page 68 6 Oil Change Pumps Porta-Quick™ The Porta-Quick™ Portable Oil Changer makes quick, clean and easy oil changes on-board any boat, because it uses the vessel’s own power supply to operate the powerful oil reservoir mounted flexible impeller pump. ■ Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protected). Size: 155/8" high x 131/2" diameter (35cm x 34cm). Hose - 1/2" (13mm) ID x 48" (120cm) long. Probe - 1/4" (6.5mm) OD x 40" (100cm) long. ■ 14 Quart (13 litre) container easily handles two engines. Weight: 9lb (4.1kg) ■ Sturdy bronze pump head. 17800-2000 ■ High temperature resistant Teflon™ dip-stick probe. 17800-2024 24 volt DC, fuse 8 amp Oil Changer. 9200-0023 Replacement Nitrile Impeller. ■ Non-collapsible thick wall suction hose. ■ Garden hose thread adapter included, for dip-sticks with GHT male threaded ends. NEW Environmental responsibility is a key factor today and the Jabsco Maintenance Pad uses proprietary technology to absorb, encapsulate and biodegrade used engine oil. ■ Handles 5 Quarts (4.72 litres) of used engine oil. ■ Also suitable for other hydrocarbon based fluids. Size: 22" x 22" x 1.5" (558mm x 558mm x 38mm) Weight: 2.5lb (5.5kg) empty 17890-0000 Maintenance Pad 12 volt DC, fuse 15 amp Oil Changer (Non CE). DIY Oil Changer ■ Passes EPA, TCLP ‘Toxic Characteristic Leaching Potential’ and 'One Drop Rule Tests'. These robust pumps make oil and diesel transfer simple and easy for fixed installation systems. The Junior Gear Puppy can produce 3.5 gpm (14 lpm) and the Gear Puppy can produce up to 6.5 gpm (25 lpm) and handle viscosities up to 150cs Size: Weight: 6lb (2.7kg). ■ Fully assembled. ■ Inlet filter supplied. 17850-1012 ■ Suitable for oils up to 150 Cs. ■ 14 Quart (13 litre) container. 15" high x 14" diameter (35cm x 34cm). 12 volt DC, fuse included. *Only available in North America. Gear Puppies The DIY Oil Changer is simple to use, and offers quick and easy oil changes for the leisure boat owner. ■ Rugged bronze construction. Size: 23220-Series: 3" x 6.5" x 5.5" (8cm x 16.6cm x 13.6cm). 23230-Series 4" x 7" x 7" (9.5cm x 17.5cm x 17.8cm). Weight: 23220-Series 4.8lb (2.2kg). 23230-Series 7lb (3.2kg). 23220-2012 12 volt DC, fuse 10A, Junior Gear Puppy. 23220-2024 24 volt DC, fuse 5A, Junior Gear Puppy. ■ Tested for 1400 cycles. ■ Complies with USCG 183.410 and ISO 8846 MARINE (ignition protection). 23230-2012 12 volt DC, fuse 15A, Gear Puppy. ■ 8' (2.49m) dipstick hose. ■ Self priming to 3ft (1m). 23230-2024 24 volt DC, fuse 7.5A, Gear Puppy. ■ 15 minute duty rating. Permanent Oil Drain Hose Kit Flat Tank Oil Changer The Jabsco Flat Tank Oil Change System will extract up to 50 weight oil at a temperature of 70°F (21°C) through the engines dip stick tube in usually less than 5 minutes. The new 14 quart (13 litre) flat tank design makes for a clean and simple oil change on any boat and allows trouble-free disposal due to the stable, easy to carry design. more stable use. ■ 7 ft (2.1m) power leads with color coded alligator clips. ■ 8 ft (2.4m) Heat Resistant Teflon™ Dip Stick Probe. ■ Ideal for most marine engines. ■ Complies with USCG 183.410 and ISO 8846 Marine (Ignition Protection). Size: 19" high x 12" wide x 6.5" deep (483mm x 305mm x 165mm). ■ Powerful suction pump with integral On/Off switch. 17860-0012 The Jabsco Oil Drain Hose includes a drain plug fitting, oil drain hose assembly, hose hanger and a cap. This provides an easy method of connecting to several pump types for neat and easy oil removal. ■ Hose hanger secures hose end above oil. ■ Threaded cap seals hose end. Size: Hose - 3/8" ID x 48" long Drain fitting - 1/2"-20 thread. Weight: 1lb (0.5kg.) 18080-0000 Hose & Drain Fitting. ■ Reinforced flexible oil rated drain hose. Carton: 12 Kits. ■ 1/2"-20 threaded oil drain fitting with two hose connection points to assure hose is oriented in desired direction. Not recommended for automobiles with drainplugs exposed to potential road hazard damage. Weight: 5lb (2.3kg). ■ Complete - ready to use. 12 volt DC, fuse 5 amp. Oil Changer System ■ 14 Quart (13 litre) NEW flat tank design for Oil Change Pump The Oil Change Pump is the same high quality pump used in the Jabsco multi-engine Oil Change System. The powerful pump can change oil in a typical V-8 engine in just minutes. Fitting: Connections for 3/8" NPT male threaded fitting. Size: 77/8" long x 33/4" wide x 47/16" high (20cm x 10cm x 11cm). Weight: 9lb (4.1kg). 51/4" high x 107/8" wide x 11" deep (13cm x 28cm x 28cm). The Oil Change System consists of a robust self-priming flexible impeller pump mounted to an easy to install base and coupled to a five port manifold, factory fitted with three full flow ball valves. 17820-0012 ■ The system includes a pump reversing switch to pump used oil out and new oil in. 12 volt DC, fuse 15 amp Oil Change System. 17820-0024 24 volt DC, fuse 8 amp Oil Changer System. 9200-0023 Replacement Nitrile Impeller. Additional 1/2" Ball Valve. Size: Ball Valves - 1/2" NPT. Weight: 9lb (4.1kg). 17830-0012 12 Volt DC, fuse 15 amp Oil Change Pump. ■ The system cover includes a hinged valve cover to protect them from being accidentally opened. 17830-0024 24 Volt DC, fuse 8 amp Oil Change Pump. ■ The valve cover will not close after an oil change unless valves are securely closed. 98024-0000 ■ Reversing switch guard to avoid accidental activation. 9200-0023-P Nitrile Impeller. ■ Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protected). For service and spare parts listing see page 185. ■ Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protected). For service and spare parts listing see page 185. ■ Pump is reversible to both drain and refill engine oil. ■ Self-priming to 3ft (1m) of lift. ■ Includes /8" NPT full flow ball valve. 3 68 Maintenance Pad Transfer Pumps Oil Change and Diesel Transfer Pumps Oil Change Pumps 6 69