• Extended Life 5,000 Hour Motor • Tough Reinforced Thermoset Plastic Housing • Mounts To Any Flat Surface • Slip-On Inlet Ducting Connection • Efficient High Volume Air Flow • Low-Current Draw • Corrosion-Resistant Materials Throughout • N.M.M.A. Type Accepted • Meets USCG Regulation 183.410 and ISO 8846 MARINE for Ignition Protection • Complies with ISO 9097 MARINE • Conforms with BSENinterference Supression 50081-2 for of Electro-magnetic SPECIFICATIONS - Flangemount Model 35760-0092 35760-0094 Air Flow Voltage Amps Air Flow Voltage Amps Fuse Size FLEXMOUNT MOUNTING Fuse Weight Size lb (kg) SPECIFICATIONS - Flexmount Model CONTINUOUS DUTY 4” BLOWER Mount blower on flat bulkhead surface in highest part of compartment free from spray or deck wash. Blower may be rotated in mounting bracket to facilitate the shortest route of ducting. Use a suitable discharge fitting so that static pressure of blower will not be affected by change in wind direction. Route inlet ducting with as few bends as possible to lower 1/3 of the bilge compartment where vapors are likely to accumulate. Be sure ducting is positioned below top of engine stringers but not so low as to become submerged in bilge water. Locate pickup to take advantage of natural air flow direction. INSTALLATION INSTALLATIONS MUST MEET APPLICABLE SECTIONS OF TITLE 33, PART 183; SUBPART K, USCG VENTILATION REGULATIONS. NOTICE: Blowers should be mounted away from extreme heat (more than 130°F) to prevent distortion of blower wheel or housing. OPERATION: See following warning placard statement: FLANGEMOUNT MOUNTING Mount blower on flat bulkhead surface in highest part of compartment free from spray or deck wash. Cut a 3-5/8” hole in bulkhead and secure blower with washers and No. 10 screws ( NOTICE: Tighten screws evenly to avoid flange damage). Use a suitable discharge fitting so that static pressure of blower will not be affected by change in wind direction. Route inlet ducting with as few bends as possible to lower 1/3 of the bilge compartment where vapors are likely to accumulate. Be sure ducting is positioned below top of engine stringers but not so low as to become submerged in bilge water. Locate pickup to take advantage of natural air flow direction. THE “WARNING” PLACARD SUPPLIED WITH BLOWER MUST BE MOUNTED ADJACENT TO ENGINE IGNITION SWITCHES (ALL LOCATIONS) TO COMPLY WITH TITLE 33, PART 183; SUBPART K, USCG VENTILATION REGULATIONS. * *Additional warning placards are available from factory by

Use stranded copper wire. For lengths up to 25 feet (7,6 m) from power source: Use 12 gauge wire for 12 volt and 14 gauge wire for 24 volt. Use larger wire for longer lengths. Use a 10 amp rated on-off switch in positive side of circuit (Model 44960-0002). Circuit must be protected with a fuse. Suggested fuse sizes are listed in the specification table. MARINE SWITCH PANELS BILGE BLOWER O N BILGE BLOWER 44960-0002 LIGHTED SWITCH W/BOOT SPST Part Description Part Number 1 Motor Kit (includes mounting nuts) 12 Vdc 18753-0605 24 Vdc 18753-0606 Blower Housing Blower Wheel Blower Housing Screw 8 x...

BLOWER PERFORMANCE

DIMENSIONAL DRAWING - Flangemount Inches (Millimeters) DIMENSIONAL DRAWING - Flexmount Inches (Millimeters) One Year Limited Warranty A. LIMITED WARRANTY: Xylem warrants that at the time of shipment, the products manufactured by Xylem and sold hereunder shall be in conformity with applicable written specifications and descriptions referred to or set forth herein, free from defects in material and workmanship, merchantable, and suitable for a particular purpose, provided such is implied by State law under the circumstances of this sale. WARRANTY, CONTRACT, NEGLIGENCE, OR STRICT LIABILITY ARISING...