IX series
12Pages

Hi-Techno Pump metering pump technology! Highly precise control offers a solution for every chemical dosing application.

A new generation of advanced metering PVDF head IX-C150TCFJ-TB-E Capacity: 1 0.2 - 150 L/h IX-C150TCR-TB-E IX-C060TCFJ-TB-E Capacity: IX-C060TCR-TB-E 0.08 - 60 L/h

IX series pump technology! Highly precise control offers a solution for every chemical dosing application. Iwaki’s IX Series are digitally controlled direct-drive diaphragm pumps. Years of experience in high-end motor technology result in extremely accurate and energy efficient metering pumps with high resolution. The IX Series meet today’s demand for automated chemical delivery in industries from water treatment to chemical process. 750:1 1000 mPa•s ±1% UP TO Turn down ratio High accuracy Energy savings Max. viscosity 70% 1 MPa Degassing ability SUS head IX-C150S6FJ-TB-E IX-C150S6R-TB-E...

Precise chemical dosing operation and energy savings Advanced mechanism assists eco-friendliness 3

IX series A wide turn down ratio A control motor adjusts the discharge and suction speeds to meet a wide turndown ratio of 750:1. C150 Capacity 0.2 - 150L/h C060 Capacity 0.08 - 60L/h Precise chemical dosing operation The valve design maintains precise dosing at any flow rate whilst the motor regulates discharge and suction speeds to achieve high accuracy (+/-1%) all with a cost effective design from a mechanically driven diaphragm pump. Efficient pump head design is incorporated with high compression IX-C150TCR-TB-E IX-C060TCR-TB-E Fast priming without air locks is achieved with a high...

Easy operation on a Variety of applications 5

IX series series Automatic control The IX can run in analogue, pulse, batch or interval batch modes. Analogue operation Pulse operation Interval batch operation The pump operates in response to an input, (4-20mA) from a controller. When combined with a flow meter or contact head water meter, the IX pump gives a paced dose rate in proportion to the main flow rate. Timed operation is possible with simple pump programming via the keypad and is initiated with a pulse signal. Flow meter Main flow PH controller Capacity Pulse signal Current signal (4-20 mA) Time Cavitation prevention Calibration...

Construction and materials IX-C150TC, IX-C150TE IX-C150S6 Valve SUS316 O-ring TC: FKM TE: EPDM Diaphragm PTFE+EPDM Pump head PVDF Valve Alumina ceramic O-ring TC: FKM TE: EPDM Diaphragm PTFE+EPDM Pump head SUS316 Valve gasket PTFE Valve guide PVDF Valve seat TC: FKM TE: EPDM Valve guide SUS316 Valve seat SUS316 IX-C150TCR-TB-E IX-C150S6R-TB-E Pump identification IX - C 150 TC R - TB - E Drive unit Special arrangement code C Pump size 060: 60 L/h 150: 150 L/h Connection Wet-end material TC, TE, S6 Please refer to above figure. R: Thread (R) N: Thread (NPT) FD: Flange (DIN) FJ: Flange (JIS)...

IX series series Specification of controller Monitors Operation LCD 16×2 backlight LCD LED Operation / Stop / Alarm START / STOP Keypads Up MAN (Manual) MENU Down ESC Left Enter Light C060: 0.08 mL/h - 60 L/h, C150: 200 mL/h - 150 L/h Analogue control C060: 0.00625 mL/PLS - 120 mL/PLS, C150: 0.01560 mL/PLS - 300 mL/PLS Batch control EXT 4 - 20, 0 - 20, 20 - 4, 20 - 0 mA Pulse control C060: 6.25 mL/PLS - 120 L/PLS, C150: 15.6 mL/PLS - 300 L/PLS Note 1 Interval batch control Operation mode Time Capacity 0-9 day, 0-23 H, 1-59 min C060: 6.25 mL - 120 L, C150: 15.6 mL - 300 L Note 1 STOP...

Points to be observed in pump installation and piping Hi-Techno pump IX series are reciprocating pumps. Reciprocating pumps generate pulsation in the suction and discharge piping. Special consideration, (dierent from the ordinary centrifugal pumps), should be given to this point when planning the pump installation and piping. • Prevention of pipe vibration • Prevention of suction failure NPSHa > NPSHr NPSHa = Pa - Pv ± Phs - Pis * MPa Discharge side inertial resistance Pid < 0.1 MPa • Pid : Inertial resistance on discharge side *Or Pfs : whichever is the larger. (NPSH : Net positive suction...

IX series series 3 Air chamber Optional accessories / example of piping Pressure gauge Discharge piping 1 Relief valve 2 Back pressure valve Air vent Tank IX series Suction piping Drain 1 Relief valve Model RV Reciprocating pumps keep running even in closed-discharge operation, resulting in piping breakage and motor failure by overpressure without a relief valve. Always install the relief valve to prevent overpressure in a discharge line. Model Wet-end materials RV-7TE-15 RV-7TV-25 Setting pressure Connection Mass L/min (L/h) RV-7TV-15 Max. capacity MPa JIS10K Flange kg 7.5 (450) 0.3 - 0.8...

Dimensions in mm IX-C150TC, IX-C150TE (115) (386) The terminal for external control signal (47) The terminal for STOP signal Output terminal AUX terminal 294 Fieldbus terminal Option 199 (365) (45) 142 156 ) 35 (ø (ø7 6) .5) 11 135 11 102 199 (365) 142 156 EUROPE / U.S.A. : IWAKI Europe GmbH : IWAKI Europe (NL Branch) : IWAKI (Austria) GmbH : IWAKI Belgium N.V. : IWAKI Nordic A/S : IWAKI Suomi Oy : IWAKI France S.A. : IWAKI Europe GmbH : IWAKI Italia S.R.L. : IWAKI Norge AS : IWAKI Iberica Pumps, S.A. : IWAKI Sverige AB : IWAKI (Schweiz) AG : IWAKI Pumps (UK) Ltd. : IWAKI America Inc. :...