Catalogs >
ITW Switches >
Spectra_Edge-023

Spectra_Edge-023
1Pages

Catalog excerpts

SpectraEDGE SCES ranges The space saving switch for through panel mounting, where the user is expected to set the codes, or other live card access which might include two state resistor pull up/pull down applications. Principal Electrical and Performance Data at 20°C 70% R.H. Contact Ratings: Non Switching: 100Vac, 5A Switching: 1µV to 100V, 1µA to 1A up to 10VA. Uses just half the length of competitive changeover switches. Allows for through panel mounting from the edge of the PCB. 1µm hard gold plated wiping contact gives high reliability in low level circuits. Base and tape sealed for flow soldering and solvent/aqueous washing. If you have a volume requirement for a product variant not shown on this sheet, please contact us. Part Nos SCES-plus suffix Length A mm max 2 2-023 7.5 4-023 12.6 11.8 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 B C D E F G H J K L M N P R S T 8 8-023 22.7 12-023 32.9 U Length B 1 10.5 (max) 32.1 2 3 8 9 10 12.1 0.40 x 0.55 2.6 3.0 - 5.0 2.54 Humidity: BS 2011 Test Ca: 56 days. 7.62 Spectra C EDGE, CHANGEOVER d.p.d.t. SCES-G-023 series Part Nos SCES-plus suffix Length A mm max Length B mm max 6.7 1 1G2-023 7.5 11.8 2 2G2-023 12.6 16.8 3 3G2-023 17.6 1 B Soldering: solderability: < 2 seconds to wet at 235°C as per IEC 68 and BS 2011 Test T, solder bath method. 2 A Temperature: Operating range for continuous electrical use and manual operation is restricted to -55°C to +100°C for standard products. 2.54 pitch 10.5 (max) Number of d.p.d.t. Life: For the first 1000 closures the standard deviation of the change in resistance from the mean is usually less than 1m . Mechanical wear out of the sliding actuator is usually observed after 10,000 operations. Length A 20 (max) 21.9 12 . Capacitance Between Open Contacts: < 1pf at 1KHz. 8 A 6.7 4 1 Length B mm max Insulation Resistance: (at 500Vdc min.) 10,000M Dielectric Strength: 1 minute: 500Vrms 50Hz. Spectra C EDGE, CHANGEOVER s.p.s.t. SDES 023 series Number of d.p.d.t. Initial Contact Resistance: (at 10mV, 10mA max.) Typical: 10m . Max. 20m . 6 013 style: 21 (max) 7 8 Length A Length B 023 style: 20 (max) 1 10.5 (max) 2 12.1 0.40 x 0.55 2.6 4 5 3.0 - 5.0 2.54 pitch 2.54 10.5 (max) Resistance to soldering heat as per IEC 68 and BS 2011 10 seconds satisfactory at 260°C when mounted on 1.5mm PCB. 9 0.13 7.62 Please note: BS 2011 is now superseded by BS EN 60068. Components This leaflet is believed to contain the best information available at the time of printing, but is subject to change without notice. Performance figures, where quoted, are actually estimates based on our experience or that of our customers or statutory authorities. In common with all components availability there is with many factors, and users are invited to contact us in appropriate cases so that where relevant information is available it may be considered by the user. All supplies are subject to the Companys standard conditions of sale which are available on request. Luton Road, Dunstable, Bedfordshire LU5 4LJ England Telephone: 01582 662241 Fax: 01582 600767 E-Mail info@erg.co.uk http://www.erg.co.uk

Open the catalog to page 1