New Products 2015/1 Systematic innovation - 40 Pages

Add to MyDirectIndustry favorites
New Products 2015/1 Systematic innovation

Catalog excerpts

Systematic innovation. New Products 2015/ I

 Open the catalog to page 1

Experience innovation – new item products for 2015/ I. MB Building Kit System Guard and protect: The robust item Collision Guard L protects racks in loading and transit areas from collisions. This mechanical covering for corner areas in line with German health and safety guidelines DGUV Regulation108-007 acts as a fixed guard to prevent vehicles driving into racks as they take a corner. Its black & yellow hazard markings make it a high-visibility guard unit. Clean and stable: Using two new Profiles X, you can now build complete doors or cells – including centre struts – that are...

 Open the catalog to page 2

Work Bench System Half the height, all the performance! The new half-height Uprights for the item work benches offer sufficient space for two shelf levels or several Pivot Arms. At an overall height of 1500 mm, operators can still see over the half-height Upright – unlike when working at a work bench with a full-height model. Write it down, wipe it off! The whiteboard accessories complement Compound Material St, a panel element which also provides a surface that can be directly written on and used with magnets. Markers, Erasers and Cleaning Spray ensure optimum results. The Markers don’t...

 Open the catalog to page 3

Dust busted. For corner joints with smooth transitions High-end design Clean without leaving particles in joints Do you need a door that is stable or a cell with an easy-clean exterior? Thanks to these two Profiles X, the solution is simple. Three of the six grooves on Profile X 8 80x40 3N90 light – oriented around 90° – are closed. This gives it the perfect geometry for use as an external strut – both horizontally and vertically. These profiles can be used to build corners that are especially easy to clean thanks to their continuous, unbroken surface. There are no gaps where cleaning...

 Open the catalog to page 4

If an additional central strut is required, Profile X 8 80x40 4N180 light is the ideal solution. The four front and rear grooves on this profile are covered, while the two side grooves are open so they can accommodate panel elements and ac- FLT^O^ Profile X 8 80x40 3N90 light ffj^W bQl—Cn Profile features easy-to-open groove(s) W^f~O^l Profile X 8 80x40 4N180 light ffj^W PQ-'Q°l Profile features easy-to-open groove(s)

 Open the catalog to page 5

A stainless solution for a spotless finish. Fastener for profiles with closed grooves Almost invisible fixing Made from stainless steel When higher standards of cleanliness need to be met and cleaning has to be easy, profiles with closed grooves are the best option. Automatic-Fastening Set 8 N, stainless is the ideal complement. It creates a secure, strong connection between profiles. It also leaves the closed surface as intact as possible and is resistant to cleaning agents. With its help, users can satisfy the high hygiene standards of the pharmaceutical and food sectors just as easily...

 Open the catalog to page 6

The Automatic Fastener is screwed into the groove in the end face of a Line 8 Profile (anti-clockwise thread). Hexagon Socket Head Cap Screw M6 is held captive in the internal thread of the Automatic Fastener. 40 0 2 The fastener is located inside the profile cavity. To access the fastening screw just drill a hole into the profile. The grey Cap is used to close the hole. A T-Slot Nut is inserted into the groove in the second profile and forms the counterpart for the Automatic Fastener screw. If this groove in the second profile is also closed, the T-Slot Nut must be inserted from either the...

 Open the catalog to page 7

Angular accuracy. For reinforcing profile connections Now available with grey Cap Angle Bracket Sets 8 Angle Bracket Sets 8 create a friction-based connection between profiles, with no machining required. They are therefore frequently used to provide additional reinforcement for profile connections. The enclosed Cap covers over the screw heads to make cleaning easier. It also enhances the harmonious appearance of structures. The Cap for Angle Bracket Sets 8 40x40 and 8 80x80 is now also available in neutral grey. Technically identical Angle Bracket Sets 8 40x40 (0.0.411.15) and 8 80x80...

 Open the catalog to page 8

Angle Bracket 8 40x40 Angle Bracket 8 80x80 The load-carrying capacity is to be checked to ensure both conditions are met. When used to reinforce the joints of large profiles or conduits, several Angle Brackets can be used in parallel. Angle Brackets are ideal for connecting cable conduits. The rounded internal edge prevents damage to the cables. Note: Ensure the maximum permissible tensile load on the Profile Groove is not exceeded! Angle Bracket Set 8 40x40 Angle Bracket 8 40x40, die-cast zinc, white aluminium, similar to RAL 9006 Angle Bracket Cap 8 40x40, PA-GF, grey, similar to RAL...

 Open the catalog to page 9

Can be positioned anywhere along a groove Magnetic Door Stop for Clamp Profile 8 32x18 The Magnetic Door Stop fits harmoniously into the frame and holds doors closed. The closing force is 40 N. Making sure doors keep themselves shut: The Magnetic Door Stop for Clamp Profile 8 32x18 is the ideal complement to Clamp Profile 8 32x18 (0.0.373.67), which can be used to build windows and doors with especially narrow frames. Clamping springs in a special groove on the Clamp Profile hold the panel elements steady and firmly in place. Magnetic Door Stop for Clamp Profile 8 32x18 Casing, PA-GF, grey...

 Open the catalog to page 10

W Cable Entry Protector for cables with plugs W For use with the item Installation Column W Quick and clean Cable Entry Protector K76 with Sealing Brush The simplest way to route cables out of the item Installation Column: Cable Entry Protector K76 with Sealing Brush creates a flexible opening that uses several layers of flexible polyamide bristles to keep dust out. Cables can be easily fed through the bristles. The Cable Entry Protector is simply pushed onto the ends of Cover Profile 76 Al (0.0.663.41). As a result, the opening can be installed at any height. It is wide enough to allow a...

 Open the catalog to page 11

Protects freestanding objects Complies with DGUV Regulation 108-007 According to DGUV Regulation 108-007 (previously BGR 234), when a rack is loaded from a forklift or other freely steerable machinery and/or is located on a route used by such machinery, its corner areas must be protected by a mechanical cover. The robust item Collision Guard L is anchored to the ground and acts as a fixed guard to stop vehicles colliding with the rack. The L-shaped Collision Guard is 405 mm high. Collision Guard L is not joined to the rack. It provides added safety in areas where there is a high risk of...

 Open the catalog to page 12

All Item industrial applications catalogs and technical brochures

  1. Linear technology

    134 Pages

Archived catalogs