Turning & Threading Tools
465Pages

{{requestButtons}}

Catalog excerpts

Turning & Threading Tools - 1

TURNING & THREADING TOOLS TURNING & THREADING TOOLS Metric Version Catalog 2012 TURNING & THREADING TOOLS Metric Version Catalog 2012 Metric Version Catalog 2012 WWW.ISCAR.COM WWW.ISCAR.COM

Open the catalog to page 1
Turning & Threading Tools - 2

ISOTURN TOOLS AND INSERTS EXCHANGEABLE HEADS ISCAR TOOL ADVISOR r=i The Ultimate Expert in Selecting the Best Tool

Open the catalog to page 2
Turning & Threading Tools - 3

INTRODUCTION Heavy Duty Turning Fast Metal Removal (FMR) is essential, especially in roughing applications where high removal rates are desired. The new HELITURN holder with its tangentially clamped insert and the unique helical shaped cutting edges provide an exceptional solution, enabling the use of very large depths of cut and high feeds. The HELITURN SLANR/L-…TANG toolholder uses a unique tangentially clamped insert, LNMX 150616R/L-HT. The double-sided insert, with its narrow curved rake face, is clamped into the toolholder on a corresponding seat using a conical head screw. This design...

Open the catalog to page 3
Turning & Threading Tools - 4

INTRODUCTION MULTI-WEDGE Clamp Holders for ISO Turning A modular turning system with top wedge clamping. On each external holder, three different inserts can be used. On the boring bar, two types of inserts can be used. Each type of insert is clamped into a different top wedge clamp. The use of the single multi-wedge holder body or boring bar with various inserts provides flexibility in application and setup and is more economical and simple to use. Trigon (W), Rhombic (C) and Square (S), inserts are pushed against the central pin from their rear side by the wedge and clamped from the top...

Open the catalog to page 4
Turning & Threading Tools - 5

Inserts with High Helical Cutting Edge for High Metal Removal Rates The HELITURN LD family consisting of WNMX HTW, CNMX ...HTW and DNMX ... HT inserts are pressed from the most advanced SUMO TEC grades. These inserts are designed with very positive radial helical cutting edges and positive rake angles, a combination which substantially reduces cutting forces and facilitates higher productivity. The CNMX and WNMX insert corners are equipped with a wiper configuration which produces high surface finish, even at high feeds. In many cases the surface finish is sufficient for eliminating a...

Open the catalog to page 5
Turning & Threading Tools - 6

INTRODUCTION 70-300 Bar High Pressure Normal Pressure 200% Increased Cutting Conditions Excellent Chip Control for Machining Titanium, Heat Resistant Alloys and Alloy Steel A5

Open the catalog to page 6
Turning & Threading Tools - 7

INTRODUCTION ISCAR THREAD Systems Laydown Triangular Inserts 3 Cornered Inserts External Cut-Grip Inserts M-TYPE U-TYPE REGULAR TYPE Small Diameter Threading Internal Cut-Grip Inserts Partial Full Profile Profile (TIP) (TIP) GEPI Partial Profile Mini-Bore ø12.5 mm TIPI Partial Profile Mini-Bore ø20 mm PICCO for Miniature Diameters Partial Profiling 55º/60º A6 CHAMGROOVE for Small Diameters GIRQ/L for Partial Profile 55º/60º ISCAR

Open the catalog to page 7
Turning & Threading Tools - 8

isoturn TOOLS AND INSERTS B1

Open the catalog to page 8
Turning & Threading Tools - 9

Toolholder Identification System B3 External Toolholders B5 Toolholders for High Pressure Coolant B60 External Toolholders for Ceramic Inserts B73 Boring Bars B82 Cartridges B114 Insert Identification System B118 Selection Guide for Chipformers and Grades B120 Negative Inserts B124 Positive Inserts B168 Inserts for Machining Aluminum B193 Pipe Skiving Inserts B199 Ceramic Inserts B201 User Guide B2 Page B227 ISCAR

Open the catalog to page 9
Turning & Threading Tools - 10

Toolholder Identification System 1. Boring Bar 2. Bar Diameter 3. Tool Length S Steel Shank I1 A Coolant through Steel Shank A = 32 B = 40 C = 50 D = 60 E = 70 F = 80 G = 90 d C Solid Carbide Shank H = 100 J = 110 K = 125 L = 140 M 150 = N = 160 P = 170 Q = 180 R = 200 S = 250 T = 300 U = 350 V = 400 W = 450 Y = 500 X = Special E Coolant through Carbide Shank I1 Boring Bar M W L N R 4 Toolholder 5 6 7 8 S 25 S M W L N R 1 2 3 4 5 6 7 8 6. Approach Angle 90° 75° 7. Insert Clearance Angle 60° 45° 0º A B D 90° N B 75° 91° 93° G F E 5º 95° J K 107.5˚ 7º 11º L 75° N Q 93° 72.5° U V 15º D R...

Open the catalog to page 10
Turning & Threading Tools - 11

4. Clamping System 5. Insert Shape P C 35˚ 80˚ Lever Lock Top Clamp Iscadex W V D 55˚ 80˚ S M...W Rigid Clamp SC - Screw Clamping C 60˚ Top Wedge Lock 25 25 M 9 10 3 – W 11 S R L 12 08 T 80˚ L W 11 – 08 D Q 12 55˚ K 9. Shank Height 8. Hand of Tool 10. Shank Width 11. Insert Size Cutting edge length R T h l h b R R N N l S CD EV l l W l L L Axial γ a and Radial γ r Rake angles 12. Wedge Lock W-Top wedge + MW-Multi-wedge γr + + γa γr - - Toolholder S- For Swiss type machines + - γa Boring Bar

Open the catalog to page 11
Turning & Threading Tools - 12

External Toolholders PLANR/L-TANG Lever Lock Toolholders for LNMX.. Tangentially Clamped Inserts 93° h h f b l2 l1 Right-hand shown Designation PLANR/L 2525M-15 TANG PLANR/L 3232P-15 TANG PLANR/L 3232P-22 TANG PLANR/L 4040R-22 TANG h b l1 l2 f Ga° Gr° 25.0 32.0 32.0 40.0 25.0 32.0 32.0 40.0 150.00 170.00 170.00 200.00 25.0 32.0 32.0 40.0 30.0 37.0 37.0 47.0 -6 -6 -6 -6 -6 -6 -6 -6 Inserts LNMX LNMX LNMX LNMX 1506..R/L 1506..R/L 2210..R/L 2210..R/L For inserts, see pages: LNMX-HM (B167) • LNMX-HT (B166) • LNMX-WG (B167). Spare Parts Designation PLANL 2525M-15 TANG PLANR 2525M-15 TANG PLANL...

Open the catalog to page 12
Turning & Threading Tools - 13

TANGENTIAL LINE Toolholders for LNMX Tangentially Clamped Inserts Right-hand shown •ap max for facing: LNMX 11-2.8 mm, LNMX 15-3.8 mm, LNMX 22-5.8 mm For inserts, see pages: LNMX-HM (B167) • LNMX-HT(B166) • LNMX-WG (B167). Spare Parts

Open the catalog to page 13
Turning & Threading Tools - 14

PLFNR/L-TANG Lever Lock Holders with Tangential LNMX Inserts for Facing and Longitudinal Heavy Turning 91° 93° l2 h h b f l1 Designation PLFNR/L 2525M-15 TANG Right-hand shown h b l1 l2 f Ga° Gr° Inserts(1) 25.0 25.0 150.00 28.0 32.0 -6 -6 LNMX 1506..L/R • ap max for longitudinal turning is 5.8mm (1) Right-hand insert for left-hand holder • Left-hand insert for right-hand holder For inserts, see pages: LNMX-HM (B167) • LNMX-HT (B166) • LNMX-WG (B167). Spare Parts Designation PLFNL 2525M-15 TANG PLFNR 2525M-15 TANG (1) Key T-6/5 T-6/5 Seat Screw TLN 15R-HT(1) TLN 15L-HT(1) Key 1 Screw 1...

Open the catalog to page 14
Turning & Threading Tools - 15

SLBNR/L-TANG External 75° Lead Toolholders for Tangentially Screw Clamped Inserts 75° h h f 75° b l2 l1 Right-hand shown Designation SLBNR/L 4040R-22 TANG h b l1 l2 f Ga° Gr° Inserts 40.0 40.0 200.00 35.0 35.0 -7 -4 LNMX 2210..R/L For inserts, see pages: LNMX-HT (B166). Spare Parts Designation SLBNL 4040R-22 TANG SLBNR 4040R-22 TANG B8 ISCAR Seat Seat Screw Screw Key TLN 22L-HT TLN 22R-HT SR 10500401 SR 10500401 SR 14-591/L-SN SR 14-591/L-SN T-7/5 T-7/5 Torx Blade T-Handle BLD T20/S7 BLD T20/S7 SW6-T SHORT SW6-T SHORT

Open the catalog to page 15

All ISCAR Tools catalogs and technical brochures

  1. MILLING

    11 Pages

  2. THREADING

    5 Pages

  3. ITSBORE

    6 Pages

  4. COMBICHAM

    5 Pages

  5. SWISS-CUT

    9 Pages

  6. CUT-GRIP

    7 Pages

  7. TANG-GRIP IQ

    40 Pages

  8. FLASHTURN

    28 Pages

  9. ISCAR INdustry

    24 Pages

  10. catalog 2015

    324 Pages

  11. JET HP Line

    60 Pages

  12. Heat Exchanger

    28 Pages

  13. Milling systems

    593 Pages

  14. TANG-GRIP

    40 Pages

  15. FLASH-TURN

    28 Pages

  16. IQ New Products

    184 Pages

  17. GrooveTurn

    372 Pages

Archived catalogs

  1. Combicham

    4 Pages