Application area Drive for unit handling conveyor systems, such as transporting cardboards, containers, workpiece carriers or tires at normal ambient temperature. Suitable for straight conveyors, small belt conveyors and especially zero-pressure accumulation conveyors. Also usable in shuttle systems, aligning conveyor segments or transfers to other "conveyor system branches". Compact design The motor integrated in the tube allows a very compact design of the conveyor system. Very energy-efficient The brushless drive features an energy recovery in braking. The conveyor system can operate without pneumatics or conventional drives, which must be operated continually. Flexible possible applications RollerDrive is available in all types of versions, allowing it to be used in all types of different conveyor systems. For the user, this translates into a single interface instead of many. Depending on the application area, PolyVee, round or toothed belts can be used for the transmission of force. Nine gear ratios allow selecting the perfect pairing between speed and torque. The electronic holding brake (Zero-Motion-Hold) holds conveying goods in position, even on gravity conveyors. Low-noise The use of decoupling elements achieves particularly low-noise running. Maintenance-free and installation-friendly The drive with internal commutation electronics does not require any maintenance. It features an overload protection that prevents damages due to overtemperature or blockage. It is connected securely without complex screw connection by using a motor cable with 5-pin snap-in plug.

Rated voltage Power Rated current Starting current Max. noise emission (mounted) Length of motor cable Max. reference length Ambient temperature in operation Motor shaft Anti-static version Tube wall thickness Tube material Tube sleeving ROLLERDRIVE SERIES EC5000 0 50 mm, cylindrical, IP54, for 0 to 40 °C 24 V 35 W 2.4 A 5.5 A 55 dB(A), application-dependent 500 mm 1500 mm 0 to 40 °C Stainless steel, 11 mm HEX, thread M12 x 1 Yes(< 106 0) 0 50 mm: 1.5 mm 0 51 mm: 2 mm Zinc-plated steel, stainless steel PVC sleeve 2 mm, 5 mm PU sleeve 2 mm Lagging 2 to 5 mm Maximum load capacity The maximum load...

Design versions 20 W Gear ratio Maximum conveying Minimum conveying Rated torque Acceleration torque Continuous blocking speed speed [Nm] [Nm] torque Gear ratio Maximum conveying Minimum conveying Rated torque Acceleration torque Continuous blocking speed speed [Nm] [Nm] torque

Gear ratio Maximum conveying Minimum conveying Rated torque Acceleration torque Continuous blocking speed speed [Nm] [Nm] torque Before the run-in, the values may differ up to ±20 %. After a run-in phase, the values vary only in the range of ±10 % for 95 % of all RollerDrive used. Planning basics General technical information Rollers | Conveying elements | RollerDrive | Controls | Accessories

ROLLERDRIVE SERIES EC5000 ø 50 mm, cylindrical, IP54, for 0 to 40 °C The dimensions of the conveyor roller depend on the shaft version. A sufficient axial play is already taken into account, so that only the actual lane width between side profiles is required for ordering. = Reference length/ordering length = Installation length, inside diameter between side profiles Without grooves Fig.: With female thread 13.1 Fig.: With hexagon spring shaft Grooves C D 13.1 Fig.: With female thread

Rollers | Conveying elements | RollerDrive | Controls | Accessories ROLLERDRIVE SERIES EC5000 ø 50 mm, cylindrical, IP54, for 0 to 40 °C Fig.: With hexagon spring shaft PolyVee drive head 13.1 Fig.: With female thread 5 General technical information Fig.: With hexagon spring shaft Round belt head 13.1 Planning basics Fig.: With female thread

ROLLERDRIVE SERIES EC5000 ø 50 mm, cylindrical, IP54, for 0 to 40 °C 35W Fig.: With hexagon spring shaft 50W Toothed belt head Fig.: With female thread