![Intellisense Microelectronics - logo](https://img.directindustry.com/images_di/logo-p/L204563.gif)
Catalog excerpts
![Counting sensor DS series - 1](https://img.directindustry.com/pdf/repository_di/204563/counting-sensor-ds-series-1053958_1m.jpg)
IMSModel DS2020/2030/3040/4050INSTRUCTION MANUAL! WARNING Thank for you selecting IMS product.This sheet primarily describes precautions required in installing and operating the product.Before operating the product, read the sheet thoroughly to acquire sufficient knowledge of the product. For your convenience, keep the sheet at your disposal. Failure to follow these instructions may result in serious injury or death: Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices,etc.) Failure to follow these instructions may result in product damage: Do not use this unit over rated voltage; Do not use this unit where there is flammable or explosive gas; Do not use this unit where there is vibration or impact; In cleaning the unit, do not use water or an oil-based detergent. *(1):Effective areas for material testing should be large enough to ensure that no collision or overlap occurs in the area;*(2):Minimum material size without leakage or miscounted in sensing area. □ Features ' Suitable for all types of materials, metal or non-metal ' Fast Response time, down to 1ms ' On-delay^Off-delay can be set ' High performance ASIC with high immunity to EMI and environmental interference 1Built in algorithm to calculate the volume of passing object ' Strong metal structure with M8 connector □ Control output circuit diagram • NPN open collector output Reset time • PNP open collector output Response time V:Channel spacing ,n:number(mm) | Tn:channel number,no need to fill in single channelj Length of sensing area,no need to fill in the ring series | Width of sensing area , Vn_[Channel spacing NumbeH Unit:mm □ Sensitivity adjustment Model opetatioA\resolution mode CX/DS Frame series RX_Ring series EX_Slot series PG Miniature *(1) :Accuracy refers to the smallest particle size to achieve no blind area detection; *(2) :Non-standard structure can be designed. For granules less than 5mm: HD mode; For small irregular objects: HD + off-delay mode; For larger objects: LS mode; For larger objects with slender tail: LS + off-delay mode; Make sure that the sensing window is large enough to avoid collision.
Open the catalog to page 1![Counting sensor DS series - 2](https://img.directindustry.com/pdf/repository_di/204563/counting-sensor-ds-series-1053958_2m.jpg)
ON-delay Off-delay Sensing condition ON-delay OFF-delay ON/OFF -delay □ Caution for using 1 The sensor has the function of automatic adjustment and can actively identify the operating environment. Please fix the sensor before power on. 2V When powered on, in the first 3 to 5 second, the yellow LED in sensor will blink - sensor is adjusting itself to optimal setting. During this period of time, do not do anything that can influence the operation of the sensor, leave the sensor to itself until the yellow LED stop blinking. If the yellow light keeping blinking for a long time without stopping,...
Open the catalog to page 2All Intellisense Microelectronics catalogs and technical brochures
-
IMS liquid level sensor
2 Pages
-
DSA
1 Pages
-
CX6080 and EX6080 Series
2 Pages
-
Label sensor LABS_O1700N
2 Pages
-
Counting sensor PG series
1 Pages
-
T18
2 Pages
-
PM Series
2 Pages
-
SPX67 Series
2 Pages
-
LD_outdoor sensor
2 Pages
-
BA photoelectric sensor
2 Pages
-
E3JM photoelectric sensor
2 Pages
-
5 in1 digital tire guage
1 Pages
-
digital pressure gauge
1 Pages
-
E3Z-T photoelectric sensor
2 Pages
-
light curtain
2 Pages
-
Fork sensor BWL
2 Pages
-
E3Z-F series
2 Pages
-
E3S50
2 Pages
-
E3S30
2 Pages
-
E3S15
2 Pages
-
E3S10
2 Pages
-
E3TA Series
2 Pages
-
E3FA Series
2 Pages
-
IMS product overview
8 Pages