PTMExFG / PTMExFBFG Applications Pressure transmitters model PTMEx are suitable for liquid and gaseous media that do not corrode stainless steel. When connecting to a certified intrinsically safe circuit, the instruments have the type of protection II 2G Ex ib IIC T6 Gb according to ATEX. Two basic models are available: Overpressure Model PTMEx 0 - 1 bar to 0 - 400 bar Model PTMExFB 0 - 1 bar to 0 - 60 bar both versions also for vacuum and compound ranges (with ventilation to the atmosphere) Absolute pressure (a) 0 - 1 bar to 0 - 25 bar (reference point zero absolute) The pressure transmitters are temperature-compensated and provide a calibrated output signal. The robust construction enables the application under difficult conditions, e.g. in shipping. EMC-Examination The pressure transmitters fulfil the stability requirements for the industrial sector, for residential and commercial areas according to the European standard and hence grant their electromagnetic compatibility. Construction The pressure transducer element is welded in the pressure connection piece. A thin stainless steel diaphragm separates the elementary sensor from the medium. For pressure ranges from 0 - 250 bar onwards, a thin film sensor is directly welded to the pressure connection piece. Standard Version Construction Type Installation length: standard Process Connection PTMEx : G % B (%" BSP), 1.4404 (316 stainless steel) PTMExFB: pressure connection with membrane flush welded G % B (%" BSP) according to DIN 3852 Measuring Cell / Sensor Measuring cell: 1.4404 [316 stainless steel (piezo)] 1.4542 [630 stainless steel (thin film)] Diaphragm (placed inside): 1.4404 [316 stainless steel (piezo)] 1.4542 [630 stainless steel (thin film)] Sensor Sealing - (measuring cell welded) Case Stainless steel, case protection type IP 65 Internal space ventilation for pressure ranges < 16 bar by plug screw fitting Pressure Ranges / Overload Pressure range-dependent, typically at least 2-fold, details see pressure range table on back of the page Output Signal 4...20 mA, 2-wire technique Measuring Accuracy 1) < ± 0.2 % of full scale value, pressure ranges > 60 bar ± 0.3% of full scale value Temperature Ranges Storage temperature: -40 ... + 90 °C (-40 ... +194 °F) with temperature decoupler: -10 ... +140 °C (+14 ... +284 °f) Temperature Influence in the Rated Temperature Range Zero point: < 0.2 % / 10 K Measuring span: < 0.2 % / 10 K Reference Temperature 20 °C (68 °F) Long-term Stability of Zero Point and Span Better than ± 0.25 % p.a. Reverse Voltage Protection Available Electrical Connection Angular plug connector according to DIN EN 175301-803, 3-pin + protective contact; For assuring the electromagnetic compatibility (EMC), please use a shielded cable (e.g. LP/LiMYCY). The shield has to be connected to the case. Electronics Silicone-cast Sensor Filling Piezo: silicone-free synthetic oil Thin film: without Power Supply 6 ... 30 V DC, max. acceptable operating voltage 30 V DC Influence of the Power Supply < 0.1 % of full scale value / 10 V Load Impedance 2-wire switching RBmax = (Ub - 6 V) / 0.02 A Load Impedance Influence For load impedance changing 500 Q < 0.1 % of full scale value Position of Installation Any (standard vertical) Ex-Approval CENELEC-Approval ATEX Explosion control intrinsically safe TUV 04 ATEX 2432 X © II 2G Ex ib IICT6 Gb Umax < 30 V DC Imax < 150 mA INSTRUMENTS TO INDUSTRY LTD Euro Works - Hawksley Industrial Estate - Hawksley Street Oldham - OL8 4PQ - United Kingdom

* accuracy ± 0.3 % of full scale value ** for intermediate pressure ranges upon request Flame arrester "Adapt-FS" ("flame penetration protection") Variant 1 according to data sheet 11001, made of 1.4571 (316 stainless steel) / cannula 1.4301 (304 stainless steel), process connection G % B (%" BSP) according to DIN EN 837-1, with CE-Type Examination Certificate PTB 99 ATEX 4023 X according to standard 94/9/EC, marking of this protection system: ©IIG M C Basic model: diaphragm placed inside PTMEx diaphragm flush welded PTMExFB no additional code letters FG Case configuration: standard case field...

Standard Case Field Housing code letters FG (no additional code letter) Cable connection ventilation via cable protection type IP 67 Circular plug connector with screw plug, ventilation via cable protection type IP 65 Plug connector DIN EN 175301-803 ventilation via plug screw fitting protection type IP 65 Screwed cable gland M 16x1.5 ventilation via sinter filter, IP 65 Option: ventilation via cable, IP 67 Weight for standard case: approx. 0.200 kg with temperature decoupler + approx. 0.050 kg Weight for field housing: approx. 0.460 kg with temperature decoupler + approx. 0.050 kg Options Temperature...