INOXPA PUMPS TOOLKIT

Product catalog summary

Introduction
Pumps require regular maintenance to ensure longevity. INOXPA has developed a toolkit to simplify and secure the maintenance of their pumps. The toolkit includes specific tools and shims for various pump types, emphasizing the importance of using original spare parts and a robust maintenance program.

Mechanical Seal Mounting Tools
The toolkit includes a variety of mechanical seal mounting tools made from black nylon, designed for different pump models such as KIBER, TLS, SLR, RV, EFI, and KVB. Each tool is tailored to fit specific pump sizes and configurations.

Instructions for Use

ESTAMPINOX EFI: Place the tool on the shaft and secure it by screwing the shaft via the pump lantern.
PROLAC HCP with Double Seal: Insert the tool to maintain a 3 mm separation between the double seal ring and cover, then secure with an Allen key.
KIBER KS: Fit the seal cover into the tool, position it on the pump, and secure it.
SLR and TLS: Position the rotating seal part onto the sleeve, push it into the tool, and tighten the studs.
RV: Place the tool on the shaft, remove the protector, and secure it via the pump lantern.
KVB: After removing the pump casing, fit the seal cover into the tool and secure it via the pump lantern.

Lobe Tightening and Anti-Rotation Tools for SLR
These tools prevent rotation during maintenance and allow for secure tightening or loosening of pump lobes.

Impeller Adjustment Shims for PROLAC HCP
These shims are used to adjust the impeller position, ensuring proper alignment and function.

Adjustment Shims for SLR and TLS
These shims are used to adjust various components within the pump, ensuring optimal performance.

Recommendations
It is advised to consult each pump’s instruction manual for proper tool usage to ensure maintenance is performed correctly.

Contact Information
INOXPA S.A.U., Telers, 60, 17820 Banyoles - Spain, Tel. +34 972 57 52 00, [email protected], www.inoxpa.com

Catalog excerpts

PUMPS TOOLKIT

Open the catalog to page 1

INTRODUCTION Pumps require regular maintenance throughout their useful life. We have designed a set of specific tools for INOXPA pumps to make maintenance both simpler and safer. Correct use, original INOXPA spare parts and a good maintenance program are the three key factors to guarantee a longer useful life of our pumps. The INOXPA pump tool case contains tools and shims for all types of pumps.

Open the catalog to page 2

1 MECHANICAL SEAL MOUNTING TOOL KS 60/80 BLACK NYLON 2 MECHANICAL SEAL MOUNTING TOOL KS 40/50 BLACK NYLON 3 MECHANICAL SEAL MOUNTING TOOL KS 25/30 BLACK NYLON 4 MECHANICAL SEAL MOUNTING TOOL KS 20 BLACK NYLON 5 MECHANICAL SEAL MOUNTING TOOL TLS 2/3 BLACK NYLON 6 MECHANICAL SEAL MOUNTING TOOL TLS 1 BLACK NYLON 7 MECHANICAL SEAL MOUNTING TOOL SLR 0/1 BLACK NYLON 8 MECHANICAL SEAL MOUNTING TOOL SLR 2/3 BLACK NYLON 9 LOBE ANTI-ROTATION TOOL SLR 2/3/4 BLACK NYLON 10 LOBE ANTI-ROTATION TOOL SLR 0/1 BLACK NYLON 11 LOBE TIGHTENING SCREW SLR 3/4 F-155 13 LOBE TIGHTENING SCREW SLR 0/1 F-155 14 MECHANICAL...

Open the catalog to page 3

INSTRUCTIONS Mechanical seal mounting tools For ESTAMPINOX EFI Place the tool on the shaft and push on as far as possible. Then screw the shaft via the lower part of the pump lantern. For PROLAC HCP with double seal After removing the protection, insert the tool through the side of the lantern to ensure 3 mm of separation between the double seal ring (position 30) and the double seal cover (position 10). Then use an Allen key to screw the double seal ring threaded stud (position 55). For KIBER KS Place the seal cover inside the tool, fit it into position on the pump and screw on the seal cover....

Open the catalog to page 4

Lobe tightening screw and anti-rotation tool for SLR Place the anti-rotation tool between the lobes to prevent any rotation and use the tightening tool to screw or unscrew the pump lobes. Impeller adjustment shims for PROLAC HCP Fit the pump shaft (05) and the clamp (17) onto the motor shaft. Slightly tighten the clamp’s Allen screw (51E) and check that the pump shaft (05) can still move. Place the shaft clamp (17) into position. Fit the cover (03) and the screws (51A). Fit the impeller (02) onto the pump shaft and tighten it using the blind nut (45). Place an open-ended spanner between the planes...

Open the catalog to page 5

INOXPA S.A.U. Telers, 60 17820 Banyoles - Spain Tel. +34 972 57 52 00 [email protected]

Open the catalog to page 6

INOXPA PUMPS TOOLKIT

INOXPA PUMPS TOOLKIT

Catalog excerpts

All INOXPA catalogs and technical brochures