WARP Radar systems
12Pages

WARP Radar systems

WARP Radar technology measures a wide variety of pipe products contact-free, precisely, and flexibly and sustainably increases product quality through increased process and quality data transparency. The WARP products are not only suitable for accurately analysing smooth and corrugated pipes directly in the line, but also for mobile quality inspection. The consistent digitization and automation of extrusion lines is a prerequisite for achieving the increasing quality and sustainability targets together with our customers.

INSPIRE beyond measurement WE GIVE EXTRUSION TECHNOLOGY A FRESH APPROACH WE INSPIRE THROUGH INNOVATIONS For more than 35 years, the name „iNOEX“ has been associated with pioneering technology and ground-breaking inventions for measurement and control technology. With innovative strength, a willingness to push boundaries and a wide range of products and services, we aim to inspire our customers. Bringing new technologies to market maturity as a pioneer is part of our company philosophy. iNOEX has therefore been investing in contactless and health-safe radar measurement technology since 2011...

WARP Radar sensor technology Radar technology relies on intelligent sensor technology based on FMCW microchips, with the wave being generated purely electronically on the chip. This allows non-conductive materials such as plastic to be tested non-destructively and without contact. The speed of the wave in plastic is slower compared to air and can vary between different materials. This difference in speed causes partial reflections of the incoming wave at the material transition. The travel time of these reflected echoes allows the wall thickness of the layer to be determined. In this way,...

Since no coupling medium is needed to emit and receive the radar waves, this application is very robust, reliable and independent of process fluctuations. ADVANTAGES AND FEATURES  High-precision measuring data  Up to 100 % pipe coverage and diameter measurement  Thin-point control in combination with SAVEOMAT gravimetric systems  Process analysis/process automation and complete documentation in the database system  Standardized process data interface (OPC-UA)  Simple operation thanks to automatic system centering and automatic calibration  Maintenance possible during ongoing...

WARP 8 The WARP 8 is an inline pipe measuring system for wall thickness and diameter measurement at 8 points or 4 axes. It provides all important measurement data required for manual or automated process optimization and control. In addition to the short return-of-invest time, the system offers high measurement accuracy as well as process automation and documentation functions. The static sensors allow a high resolution of the measured values in the extrusion direction. Thus, process fluctuations are precisely recorded and visible, so that effects such as short-term fluctuations in output or...

WARP 100 WARP 100 is an inline pipe measuring system for wall thickness and diameter measurement at up to 38 measuring points and 19 axes. More than 1100 measurements per second guarantee a gapless measurement. This is particularly important for pipes with high quality requirements, such as pressure or gas pipes. The maximum line speed for 100% coverage is up to 11.8 m/min. The static sensors are distributed around the pipe and continuously measure the pipe in parallel. The specially developed optics allow the alignment of the radar wave to be focused on the centre of the pipe. The sensors...

WARP CP The WARP CP is an inline measuring system with 8 radar-based wall thickness sensors for detecting the various structures of a corrugated pipe. Outer and inner diameters, as well as the wall thicknesses of the bell, crest, liner, and valley can be resolved. The system is available for large, corrugated pipes with diameters from 300 mm. The 8 sensors around the corrugated pipe scan it continuously. Since the corrugated pipe has different structures, it is therefore necessary to assign the measurement data to the corresponding position on or in the pipe. The WARP-CP algorithms do this...

WARP portable The WARP portable is a mobile, radar-based hand-held gauge for selective wall thickness measurement, specially designed for medium and large pipe extrusion as well as for sheets. The application possibilities are very flexible, whether as a quick centering aid in the start-up process, for final production control or as a stock control device. Not only wall thicknesses at pipe ends can be measured, but also the progression inside a pipe section or a sheet. The measurement itself is performed at the push of a button. The last 500 measured values including the measuring angle on...

iDM 4.0 The iNOEX Data Manager (iDM) comprises a central data logger for the collection of all process and quality data of the iNOEX systems in the extrusion line. Optimization potentials can be identified, and productspecific key figures can be analysed and evaluated. The software is installed as a virtual machine in the customer‘s network, so that no additional hardware is required. OPC-UA as a standardized process data interface, integrated with the latest measurement, control and automation solutions from iNOEX, transfers the data. A connection of legacy systems via the iDM gateway is...

WARP Products at a glance Type ± 0,03 (154 GHz Chip) WARP portable

GERMANY iNOEX GmbH Phone: +49 5422-60507-0 Fax: +49 5422-60507-101 iNOEX GmbH Maschweg 70 49324 Melle Tel.: +49 5422-60507-0 Fax: +49 5422-60507-101 P. R. CHINA Suzhou iNOEX Smart Technology Co., Ltd. Phone: +86-512 6568-0816 Fax: +86-512 6568-0820 USA iNOEX LLC Phone: +1-717 672-0870 Fax: +1-717 672-0872 TURKEY iNOEX Plastik LTD. Phone: +90 544-434-5938 Fax: +90 216-365-0837 DUBAI iNOEX Middle East Phone: +971 55860 9058 © iNOEX GmbH - All rights reserved. Reproduction in whole or in part without the written consent of the copyright holder is prohibited. iNOEX GmbH reserves the right to...