Catalog excerpts
PCD/CBN MILLING
Open the catalog to page 1Modern machining operations need to rely on the optimization of the production processes: in this respect the milling operations play a very important role and several factors contribute to its increasing significance. On one side the demand to reduce the machining time and on the other side the constant request for quality improvement as far as surface roughness and flatness are concerned, make it necessary to adopt high performance tools able to guarantee high cutting speeds and long tool life. Moreover, the trend towards stronger thinner work piece materials in response to the...
Open the catalog to page 4For every surface a non superficial approach Face milling or contouring: any milling operation can be performed by IT.TE.DI milling cutters, from the simplest cutter with cylindrical shank to the monolithic cutter with replaceable cartridges. IT.TE.DI cutters are the best answer to the most difficult challenges and are available exclusively from Ingersoll Cutting Tools throughout North America.
Open the catalog to page 5TEDI FEED® PCD &CBN Tangential Milling
Open the catalog to page 8TEDI FEED is the new line of mill with tangential inserts available with PCD and CBN inserts, single, double and full cutting edges. TEDI FEED is studied for machining operations from heavy roughing to superfinishing. Available with all holders, with cylindrical shank, monoblock or shell type configurations. A wide range of diameters, lengths and number of cutting edges guarantee the best results in every applications. FEATURES: • Suitable for high speed machining • Low cutting forces • Insert available with single tip, double tip and full edge • High number of cutting edges for high product
Open the catalog to page 9NUMBER OF CUTTING EDGES HOLDER DIMENSION CYLINDRICAL SHANK SHELL TYPE NOMINAL DIAMETER Order examples: For placing an order of a cutter body shell type ø125 with Z=18 milling + 2 wiper, please indicate the code: 2717435 The following codes are referred only to the cutter body not assembled with inserts.
Open the catalog to page 10SHELL TYPE CUTTERS - INCH / METRIC TEDI FEED® Drive notch measure (A, B) according to ISO 6462-1983 HOLDER SHAPE * Minimum diameter guaranteed with standard inserts. Refer to related table of available cutting geometry for more detail. 1 Item number refers to body only, without inserts. 2 Without internal coolant. 3
Open the catalog to page 11CYLINDRICAL TYPE CUTTERS - INCH / METRIC * Minimum diameter guaranteed with standard inserts. Refer to related table of available cutting geometry for more detail ** Without axial adjustment 1 Item number refers to body only, without inserts. 3 The weight is referred to the assembled part (cu
Open the catalog to page 12MONOBLOCK TYPE CUTTERS - METRIC TEDI FEED® MONOBLOCK TYPE CUTTERS - METRIC *Minimum diameter guaranteed with standard inserts. Refer to related table of available cutting geometry for more detail. 1 Item number refers to body only, without inserts. 3 The weight is referred to the assembled part (cutter body with cutting parts). Monoblock cutters are non-stock standard - request a quote.
Open the catalog to page 13MONOBLOCK TYPE CUTTERS - METRIC MONOBLOCK TYPE CUTTERS - METRIC *Minimum diameter guaranteed with standard inserts. Refer to related table of available cutting geometry for more detail. 1 Item number refers to body only, without inserts. 3 The weight is referred to the assembled part (cutter body with cutting parts). Monoblock cutters are non-stock standard - request a quote.
Open the catalog to page 14Inserts are screw clamped in mill body to help assembling process. Several combination of insert are available to cover a wide range of material and applications. CUTTING EDGE GRADE PCD FULL EDGE CUTTING EDGE PRODUCT LINE TEDI FEED® INSERT TYPE CUTTING EDGE GEOMETRY 15° T *Alternative grades available, please contact IT.TE.DI. for choosing the best grade.
Open the catalog to page 15RECOMMENDED GRADE FOR ALUMINUM ALLOYS WITH SI < 12 - 14% AND MAGNESIUM ALLOYS GEOMETRY Recommended for finishing not square shoulder surfaces. Suitable for light roughing too. Recommended for finishing square shoulder surfaces. Suitable for light roughing too. Suitable for roughing or for cutting material with a high impurity content. (Cubing) Suitable for finishing or roughing - general purpose. Suitable for finishing rough (gasket) surfaces RECOMMENDED GRADE FOR GREY CAST IRONS AND NON FERROUS CAST IRONS GEOMETRY Recommended for finishing not square shoulder surfaces. Recommended for...
Open the catalog to page 16SINGLE TIP PRODUCT CODE DOUBLE TIP Sample shown: right hand. PRODUCT CODE FULL EDGE Sample shown: right hand. PRODUCT CODE WIPER Sample shown: right hand. PRODUCT CODE Available upon request TEDI FEED
Open the catalog to page 17SINGLE TIP Sample shown: right hand. PRODUCT CODE DOUBLE TIP Sample shown: right hand. PRODUCT CODE WIPER Sample shown: right hand. PRODUCT CODE
Open the catalog to page 18SINGLE TIP Sample shown: right hand. DOUBLE TIP Sample shown: right hand. PRODUCT CODE FULL EDGE Sample shown: right hand. PRODUCT CODE Available upon request
Open the catalog to page 19SINGLE TIP Sample shown: right hand. PRODUCT CODE DOUBLE TIP Sample shown: right hand. PRODUCT CODE
Open the catalog to page 20TEDI MILL® The perfect answer
Open the catalog to page 22TEDI MILL is a family of cutters with replaceable cartridges with brazed PCD and PCBN cutting edges. They have been developed thanks to IT.TE.DI’s experience and research and are the result of modern solutions and accurate production checks. An important feature of the TEDI MILL is its clamping system: besides the common screw clamping, a clamping wedge is added, thus the rigidity of the cutter is increased and higher cutting speeds, feeds and tool life are attainable. The clamping wedge also prevents erosion of the cutter body from chip wash and it directs coolant directly to the cutting...
Open the catalog to page 23SHELL TYPE CUTTERS - INCH Item Number Holder Shape (*) Minimum diameter guaranteed with standard cartridges. Ref. page 31 depending on cartridge geometry. (1) Item number refers to body only, without cartridges.
Open the catalog to page 24SHELL TYPE CUTTERS - METRIC Holder Shape Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy Light Alloy (*) Minimum diameter guaranteed with standard cartridges. Ref. page 31 depending on cartridge geometry. (1) Item number refers to body only, without cartridges. Metric diameters are non-stock standard - request a quote....
Open the catalog to page 25All Ingersoll Cutting Tools catalogs and technical brochures
-
Slotters
16 Pages
-
Solid Carbide
64 Pages
-
END MILLS
58 Pages
-
Gold-Rush Catalog
13 Pages
-
HI-POS+
45 Pages
-
quadtwist
11 Pages
-
GOLD RUSH
12 Pages
-
gold max 4 slotters
5 Pages
-
EVOTEC Series 1SJ1Y
4 Pages
-
gold max 4
3 Pages
-
gold max 4 New
3 Pages
-
Plunge Cutters
20 Pages
-
ChipSurfer & Solid Carbide Cat.
116 Pages
-
Holemaking Section
46 Pages
-
Turning Section
160 Pages
-
Milling Section
94 Pages
-
Fine Gold
302 Pages
-
D'Andrea Precision Boring (INCH)
187 Pages
-
Form-Master Pro
6 Pages
-
Form-Master Cera Brochure
4 Pages
-
Form-Master Speed
6 Pages
-
Gold-Rush Catalog
1440 Pages
-
New Gold Catalog
176 Pages
-
Image Brochure
13 Pages
-
BTA DRILLS
110 Pages
-
Power-Feed+
6 Pages
-
Form-Master Wave Button
8 Pages
-
Finish-Ball
6 Pages
-
Plunging Cutters Brochure
20 Pages
-
Swiss & Live Tooling (Milling)
43 Pages
-
Hi-Pos Deka Family
12 Pages
-
Chip-Surfer & Solid Carbide Catalog
116 Pages
-
Super Catalog - Hole Making Products
166 Pages
-
2008 Product Update
60 Pages
-
Super Catalog - Toolholders
44 Pages
-
Super Catalog - Turning Products
366 Pages
Archived catalogs
-
Super Catalog - Milling Products
546 Pages
-
Hole Making Catalog
124 Pages
-
Milling Catalog
430 Pages
-
Face Mills
69 Pages
-
End Mills
123 Pages