INDUMART www.indumart.com Magnetic Flow Meter Flange Connection FTM45 with Local Indication FTM45-FW FTM45 with Remote Indication INTRODUCTION Indumart FTM45 Series of Magnetic Flow Transmitters with 4-20 or 0-10 mA and frequency/pulse output signals, proportional to the flow rate of fluids passing through, and lower and upper limit alarm outputs are ideal for very highly accurate measurement of electrically-conductive fluids’ flowrate and their total flow. Sanitary version with Tri-clamp connections Measurement accuracy of the FTM45 Series is not subject to variation of the fluid density, viscosity, temperature, pressure and conductivity. These flowmeters can measure bi-directional (positive / negative) flowrate, which will provide a very good means for precise measurement of flowrate / total flow. Remote Converter Generally, there are two classes of FTM45 Series; The model “F” as a flange connection meter (⅛" to 120" DN3 to DN3000) and the FTM45-S is a Tri-clamp sanitary connection type meter (½" to 4"). There are also two models available for field indication; the FTM45-□ L for local indication, and FTM45-□ W for remote indication of the flow parameters. Optionally, the sensor part of the these remote meters can be buriable and inherently submersible (IP68), thus ensuring suitability for installation in chambers and metering pits, which are liable to flooding. The FTM45 Series is suitable for flow measurement of homogeneous (2-phase included) and electrically conductive fluids with conductivity greater than 5 microSiemens/cm. Ground or tap water, wastewater, d i a r y, b r e w e r y, b e v e r a g e s , l i q u i d f o o d s , pharmaceuticals, slurries, cement, fly ash, pulps in mining, and concentrated pulp and paper are some of the prevalent media used for flow measurement applications of FTM45 Series. But these magnetic flowmeters are not applied for distilled water, hydrocarbons and generally non-conductive fluids. Sensor grounding may be ordered as ring or electrode. If the channel which contains the meter is insulated, the meter needs to be installed with ground ring and where the medium is abrasive, the ground ring with neck is recommended to protect and prolong the service life of the meter. The ground ring with neck is also used for mediums, such as mud, ore pulp, coal water slurries, etc. Designed from ⅛" to 118" in size with a flow velocity of 0.3 to 12 m/sec (1 to 40 ft/sec), these meters are factory-configured and calibrated to international standards to provide the user with assurance of both quality and performance of the meter. A calibration certificate is included with each flowmeter shipped to the users. An advantage of FTM45 Series is that, in most installation, it only needs a minimum of 3 pipe diameters of run upstream and 2 diameters downstream to operate (see the instruction manual or inquire for exceptions). Power supply to the flowmeter can be ordered as the city power line (110...240 AC), 24 VDC, batterypowered or dual power (24 VDC and battery). The battery-life of a battery powered meter, depending on the measurement cycle time and excitation current and power frequency, may last up to 5 years (see manual). Due to the materials and technology used in construction of these flow instruments with fully welded and maintenance-free sensors, the FTM45 series is excellent in reliability and resistance to corrosion against a majority of chemically aggressive media. For special applications, the electrode and liner materials can be specified as other materials specified by the user to stand corrosion. The converter is equipped with a flowmeter fault diagnostic system. Alarms are classified into the System Alarms (hard failures), Process Alarms (Empty Pipe) and Setting Alarms (Flow Upper/Lower Limit Alarms). The information code along with showing a bell sign is displayed on the left side of t

MODBUS RS485, HART and radio communication options are available for the FTM45 series. As an advantage, optionally, the FTM45 Series flow meters can be equipped with GPRS (General Packet Radio Service) can wirelessly communicate with a base station as far as 1 km and the base station via GPRS or CDMA (Code Division Multiple Access) mobile communication network can communicate with a supervisory computer. temperature can reach up to 120°C. But it does not have very good wear resistance. F46 has chemical and temperature resistance of PTEF, but is more resistant to abrasion. Polypropylene can stand...

SPECIFICATIONS Accuracy Medium Flow Velocity Range Flow Unit Display Total Flow Display Sensor Remote Connection Process Connection Sensor Housing Converter Flanges Measuring Tube Measuring Electrodes Grounding Rings Grounding Electrode Min. Upstream Length Min. Downstream Length Infrared Remote Control Outputs Current Output Output Error (mA) Load Resistance Frequency Output Pulse Output Eq. Wt. Pulse Output Pulse Output Width Alarm Outputs Communication (option) Electrical Isolation Baud Rate Excitation Mode Power Supply Environ. Protection Ambient Temperature 0.2%, 0.5% Electrically conductive...

ORDER CODES - Model: FTM45PROCESS CONNECTION Flange Sanitary CONVERTER / INDICATOR Local Indication* Wall-mounting Box Converter / Indicator ELECTRODE 316L Stainless Steel Hastelloy "C" Titanium Tantalum Other LINING MATERIAL Hard Rubber (<60°C) Polyurethane (<90°C) PTFE (<120°C for positive pressure only) PTFE (<120°C withstands negative pressure) F46 (<120°C for positive pressure only) F46 (<120°C withstands negative pressure) ACCURACY 0.5% 0.2% (not available for over 8" tube diameter) OUTPUT Not Required 4...20 mA, Frequency/Pulse DIGITAL COMMUNICATION No Communication Rs485 HART GPRS POWER...