TRIME-GWs: Moisture sensor for corn dryer
7Pages

Grain and product moisture measurement. Direct, representative, fast and precise with the most modern TDR technology. TRIME®-GWs GUARANTEES YOU THE FOLLOWING: direct measurement of moisture in the material continuous data logging concerning the moisture level optimum and precise process control throughout all cycles lower product value losses as the result of over- or under-drying savings in heating costs and power consumption

Over- or under-drying – mistakes that cost you money! If you work with dryers then you know the problems all too well. Hand-operated dryers are difficult to control and they can produce unacceptable results that can cost you dearly: Time-consuming sampling, goods that are either too damp or too dry, expensive after-treatment - all of that costs you time and money. For the first time, the revolutionary TRIME®-TDR technique allows for precise, continuous measurements directly during the drying process – at temperatures of up to 127°C (260°F). And regardless of the type and composition of the...

The TRIME®-GWs sensors are used for inline measurement in the widest range of materials. The results will win you over! The improved process control optimizes the cycle times, saves energy, increases productivity and reduces the amount of real work. Constant, direct displays of product moisture in the dryer make the process transparent and the operation reliable! Time- and labor-intensive samplings previously associated with conventional measuring equipment are reduced to a minimum. Today, dryers are operated based only on TRIME®-GWs measured data. 70.000,00 € Zusätzliches Umsatz- bzw....

The right TRIME® probe for every application The TRIME® probe series offers optimal probe designs for many different applications. Every probe also has an integrated temperature sensor, thus offering the option of measuring material temperature. The standard GR probe can be installed up to a depth of 150 mm directly in the grain dryer’s wall. At temperatures of up to 127°C and a measuring volume of approximately 2 liters, the GR probe offers optimal conditions for all materials that can be easily poured. With the temperature sensor attached to the tip of the rod, you can easily measure the...

Installation example of a drying plant On-line measurement during the drying process directly at the beginning of the heating zone TRIME-GWs On-line measurement of the discharge hopper Continuous monitoring and recording during grain delivery with protocol print-out log issue SONO-VIEW Installation in the control room or in the distribution cabinet Mix Process Status Normal Water Dosing Mix Overview Total Water Existing Water Runover Needed Water Needed Water Needed Water Developing of Mixer Values 0,4 0,3 Networking option Networking via PC via USB. Interface for processing the acquired...

Tested and approved by the DLG Tests of the TRIME®-TDR method conducted by DLG (Deutsche Landwirtschaftliche Gesellschaft – German Agricultural Society) have delivered convincing results. According to statements made by companies and DLG, the TRIME®-GWs system finally enables a precise drying process! DLG test results: “The system is suitable for continuous (inline) measurement of the moisture content of grains, rape-seed, sunflowers, corn and other agricultural cereals. It can be employed in a control system, e.g. for a dryer, to measure the moisture content as a controlled variable.”...

Our technical edge is your advantage! Technical Data: Power supply: Measuring range: Probe GR, WS2, GS1, GS2 0..45 Gew.% gravimetric, based on wet mass 0..70 Gew.% gravimetric, based on wet mass Standard deviation: range 0..20 Gew.%: ± 0,3 Gew.% range 20..45 Gew.%: ± 0,5 Gew.% range 45..70 Gew.%: ± 1,0 Gew.% Repeating accuracy: Transducer temperature range: -10°C..60°C advanced temperature range on request! Probe temperature range: Measurement interval: 0,5s with internal averaging from 5s...20min. Analog output: 0/4...20mA = 0 .. 100% grav. moisture 0/4...20mA = 0 .. 100°C (max. working...