Point laser sensor CONOPROBE You got a free-forming surface and no CAD data for it? Not a problem for our un and our laser-digitalization-system ConoProbe! Based on the patented method “conoscopic-holography-technology”, this system provides high resolution data of any kind of free-forming surface, that you can use afterwards for creating cutter-tracks or project tracks on it. Also for gaining data from plaster models e.g. reliefs for mint-dies this system is the perfect tool and the world market leader in this field. The software CopyMate can save the surface data as STL (triangulated points) or as grayscale image (pixels, the darker the deeper). Standard features: Very high resolution and accuracy Compact design Stand-alone system or integrated on a milling machine Measuring range in Z-direction up to 70 mm (depends on used objective lens) Laser-type: Diode laser with 655 nm wave-length, laser safety class 2 (conforms to DIN EN 60825-1) Laser sensor CONOPROBE Lenses focal length 16 mm 25 mm 50 mm 75 mm 100 mm 125 mm 150 mm 6 µm 10 µm 15 µm 20 µm 35 µm Z-(vertical) axis specification Absolute accuracy 2 µm 3 µm Reproducibility 0.1 µm 0.4 µm 1 µm 2 µm 4 µm 8 µm 10 µm Max. working range 0,6 mm 1,8 mm 8 mm 18 mm 35 mm 45 mm 70 mm Stand off 9 mm 15 mm 35 mm 60 mm 70 mm 240 mm 110 mm Linearity over operating range 0,5% 0,2% 0,2% 0,2% 0,2% 0,2% 0,2% X-(lateral) axis specification Dimension of laser point (approx.) 8 µm 45 µm 65 µm 75 µm 100 µm 100 µm 5 µm Resolution 22 µm 12 µm 15 µm 25 µm 35 µm 50 µm 50 µm Data handling Data rate up to 3000 points per second General Absolute accuracy by radius measuring 0,2 % of radius ± 2 mm Angular measurement 0 bis 85 degree Operating temperature 18 up to 35 °C Multi-Use Single Head A single head can be used just by changing the objective lens. Where with competing systems you must buy several complete instruments, with CONOPROBE you purchase one system with different lenses. Dynamic Range CONOPROBE maintains high precision and repeatability over a wide working range. In most cases, the precision and repeatability is better than 1/8000th of the working range. This is in contrast to 1/1000th of most competing systems. Bestellinformation Bezeichnung CONOPROBE, CopyMate, 50 and 100 mm lense CONOPROBE, no software, 50 and 100 mm lense 26 Fixing device for laser Extension cable for laser Surface Independant CONOPROBE measures a wide variety of surfaces which could never be measured by non-contact measurement before such as machined metals and other relatively shiny objects. It also has no problem measuring surfaces with wide variations in reflectivity. Grazing Incidence Measurement CONOPROBE is able to measure at angles very close to grazing incidence. The Forbidden Zone extends only 5 degrees from normal incidence from all directions. This again is in contrast to competing methods. The inelligent control system CAN BUS enables the measuring from nearly 90° step edges.

ICV 4030 scan The stand-alone-system ICV 4030 scan provides all advantages of the laser system ConoProbe in combination with the well proven machine ICV 4030, so that a very compact system is available. Due to its little required space the system finds its space in any work shop and by this it is our bestseller in this field of applications. With a working area of 400 x 300 mm most typical digitalization applications can be covered. Standard features Closed control loop Servo technique Servo motor control and power electronic integrated Control software WIN®-Remote and digitalization software...