Value Creator

SWING CLAMPS FOR TORQUE CONTROL Base/Washer/Flange Nut/Clamping Spindle S45C steel Quenched and tempered Black oxide finish SCM440 steel Quenched and tempered Black oxide finish Feature ・Designed for clamping-force control with a torque wrench. ・Screw-locking mechanism allows for longer clamping stroke and greater clamping force than a cam-locking mechanism. Clamping Height Clamping Stroke Rough Surface Finished Contact

Clamping Height   *) Part Number Finished Surface Contact Rough Surface Contact Min. *) Clamping height can be adjusted. The parenthesised values denote clamping height range. Part Number Turning the flange nut allows the clamp arm to swing into position for clamping. Note Do not use a power tool (impact wrench etc.) to turn the flange nut, for damage prevention. SWING CLAMPS WITH ADJUSTABLE HANDLE One-Touch type is available. Clamping Force(kＮ) Performance Curve Clamping Allowable Screw Weight Force(kN) Torque(N・m) (g)

SWING CLAMPS (Quick-Acting) Body / Clamp-Arm Holder / Hex. Head Feature ■The clamp arm swings in swift response to the turning speed of an impact wrench, for quick clamping. ■A short clamp-arm travel allows quick clamping. Note:For robotized production lines, use NUTRUNNER SWING CLAMPS.

■ Without Clamp Arm Part Number Note: The clamp arm can be replaced with a custom one of your own design. Refer to the instruction on our website for the dimensions and details. Note that the clamping force with the custom clamp arm may increase or decrease from the value above. How To Use 1. Unclamped Mode Load a workpiece. 2. Ready-To-Clamp Mode When the hex. head is turned by an impact wrench, the clamp arm swings fast to the clamping position. 3. Clamping Mode The clamp arm moves down for clamping. Using an impact wrench allows completing positive clamping in a few seconds. ■ Do not use applying...

HOOK CLAMPS imno Part Number Part Number •Compact design for applications in limited space •IBJ530I Hook-Clamp Holders are available. •Clamp that is designed to move up and down in conjunction with the tightening screw, for prevention of galling. Instead of being used with Hook-Clamp Holders, these Hook Clamps can be plugged into a custom block with receiving holes as specified on the right.

HOOK-CLAMP ASSEMBLIES Clamp Body Part Number Part Number Feature The hook clamp is designed to move up and down in conjunction with the tightening screw, for prevention of galling in the hook-clamp holder.

HOOK-CLAMP ASSEMBLIES WITH FLANGED HOLDER Clamp Body

Value Creator

HOOK CLAMPS M- Socket-Head Cap Screw Body Related Product BJ530 Hook-Clamp Holders SCM435 steel Quenched & tempered Black oxide finished Precision ground Hook Clamp Clamping Stroke Custom Block ■Machining Instruction for Custom Blocks φ２５ ＋０．０４１ ＋０．０２０ ＋０．０３４ ＋０．０１６

*) Values for use in conjunction with custom holder blocks. For use in conjunction with IBJ530I Hook-Clamp Holders, apply allowable screw torques given on the |BJ530| page. Please put grease on sliding surface to prevent galling when using in dry condition.

HOOK-CLAMP ASSEMBLIES imno Clamp Body SCM435 steel Quenched and tempered Black oxide finish Precision ground Holder S45C steel Black oxide finish Part Number

Part Number Part Number Clamping Allowable Screw Force（kN） Torque（N・m）

HOOK-CLAMP ASSEMBLIES (Flanged) Clamp Body

Part Number Feature Note Perfect for low-height clamping. Please put grease on sliding surface to prevent galling when using in dry condition. Part Number

HOOK-CLAMP HOLDERS Part Number *) Tolerances of d Diameter BJ530-04 BJ530-06 : ＋０．１ ０ BJ530-08 BJ530-10 BJ530-12 BJ530-16 : F7 **) The value to use with BJ130-10040 . ***) The value to use with BJ130-12060 or BJ130-12160 . Allowable Screw Weight Torque(N・m) (g) S45C steel Black oxide finish Note The above screw torque values are effective for installation of BJ130 BJ132 Hook Clamps. How To Use Hook Clamp BJ１３０ Cylindrical Risers BJ６００

HOOK-CLAMP HOLDERS (Flanged) Part Number Feature How To Use Suitable for low-height clamping. Part Number

HOOK CLAMPS Part Number ‘) The center of R1 is located in 5mm outside from the center of the body.

Part Number Clamping Allowable Screw Force(kN) Torque(N・m) Related Product BJ６００ Cylindrical Risers are available for additional height． Note Please put grease on sliding surface to prevent galling when using in dry condition.