Spring Clamps
22Pages

{{requestButtons}}

Catalog excerpts

Spring Clamps - 2

SPRING SWING CLAMPS VERTICAL-HANDLE HOLD-DOWN SNAP CLAMPS(Mini) VERTICAL-HANDLE HOLD-DOWN SNAP CLAMPS ANGLE ADAPTOR PUSH-PULL SNAP CLAMPS CLAMPING SPINDLES THRUST CLAMPS THRUST CLAMPS (Vertical) CLAMPING BARS PRECISION THRUST CLAMPS

Open the catalog to page 2
Spring Clamps - 4

SPRING SWING CLAMPS ★Key Point Handle clicks at the clamping end point. Body Arm Cam Shaft S45C steel SCM440 steel SKS3 steel Quenched and tempered Quenched and tempered Quenched and tempered Electroless nickel plated Electroless nickel plated Electroless nickel plated Clamping Spindle Handle Polyamide (glass-fiber reinforced) Brass Orange Counterclockwise Clamping Clockwise Clamping Advance Throw Clamp Starting Position Advance Throw Clamping Throw Clamp Starting Position Unclamping Position Unclamping Position Advance Stroke Clamping Height

Open the catalog to page 4
Spring Clamps - 5

Part Number Clamping Height *) Clamping Direction Clamping Advance L2 L3 L1 Stroke Stroke *)Clamping height is adjustable within the listed range. Part Number Clamping Weight Force (N) **) (g) **) Values at the midpoint of the clamping stroke. It varies within the listed range depending on the contact point of the clamping spindle that decides the spring tension. Feature ・Turn the handle after the arm swings into position, the cam shaft rotates along the guide pin to push down the arm. The clamping spindle contacts the workpiece and the cam shaft moves up and compresses the spring to clamp...

Open the catalog to page 5
Spring Clamps - 6

VERTICAL-HANDLE HOLD-DOWN SNAP CLAMPS (Mini) Stainless Steel Clamping Arm / Handle Clamping Spindle SUS304 stainless steel SCM440 steel S45C steel Quenched and tempered SCM435 steel Black oxide finish Black oxide finish Quenched and tempered Black oxide finish (Black Oxide Finish) (Stainless Steel) (Electroless Nickel Plated) QLSNDM08-SUS SCS13 steel SCS13 steel (equivalent to SUS304) (equivalent to SUS304) QLSNDM12-SUS SUS304 stainless steel QLSNDM08-NP S45C steel SCM440 steel QLSNDM12-NP Electroless Nickel Plated Electroless Nickel Plated Recommended Clamping Position Recommended Clamping...

Open the catalog to page 6
Spring Clamps - 7

(Black Oxide Finish) Handle Operating Clamping Weight Load (N) Force (N) (g) Part Number Part Number ・The clamp clicks when clamping is done. ・Perfect for clamping of a small part, and for use in limited space. ・Designed for fingertip handle operation. ・The handle is lockesd at the unclamping position. ・Uses a snap-on system (single locking). Handle Operating Clamping Weight Load (N) Force (N) (g) (Stainless Steel) (Electroless Nickel Plated) Part Number Handle Operating Clamping Weight Load (N) Force (N) (g) How To Use Use a BJ601 Small Cylindrical Risers to raise these clamps. Small...

Open the catalog to page 7
Spring Clamps - 8

VERTICAL-HANDLE HOLD-DOWN SNAP CLAMPS Unclamping Mode Body Clamping Spindle ZDC2 steel SCM440 steel SCM435 steel S45C steel Phenolic plastic Cation coating finish Quenched and tempered Quenched and tempered Chrome plated Black Black Black oxide finish Black oxide finish Clamping Mode ★Key Point The handle clicks at clamping end. L1 Spindle Position Recommended Clamping Position Unclamping Position Recommended Clamping Position Clamping End Clamping Stroke Incomplete Thread Length Clamp Starting

Open the catalog to page 8
Spring Clamps - 9

Part Number Part Number Handle Operating Clamping Weight Load (N) Force (N) (g) How To Set Handle To Recommended Clamping Position Clamping Clamping Spindle 1. Set the clamping spindle to contact a workpiece at clamping end position. Half of Clamping Stroke 2. Project the clamping spindle by about half of the clamping stroke and tighten the nut. ・The clamping forces and handle operating loads stated above can vary by up to ± 20%. ・When the reaction force(F) becomes greater than the clamping force, clamping is lifted. ・The long handle facilitates clamping operation. ・The handle is locked at...

Open the catalog to page 9
Spring Clamps - 10

Dedicated for Snap Clamps Body S45C steel Black oxide finish Part Number Supplied With Clamping Forces Generated in Use of Extension Arms Hex. socket head setscrew M5×0.8-14L ×2 pcs. Part Number How To Use Use to extend the clamping arm for clamping at a more distant point. Face Mounting Back Mounting Hex. socket head setscrew M5×0.8-14L Hex. socket head setscrew M5×0.8-14

Open the catalog to page 10
Spring Clamps - 11

ANGLE ADAPTOR Dedicated for Snap Clamps Cross Section X-X Cross Section X-X Part Number M6 Cap-Screw Hole M6 Cap-Screw Hole Body S45C steel Black oxide finish Dimensions of Snap Clamps with Angular Adaptor Installed QLSND QLSND Supplied With Hex.socket head cap screw M6×1-12L × 1pc. How To Use Remove the handle and then install an Angular Adaptor between the body and the handle. (Use a wrench of nominal size 9 for removal of the handle.)

Open the catalog to page 11
Spring Clamps - 12

PUSH-PULL SNAP CLAMPS Handle Link SCM440 steel S25C steel ZDC2 steel Cation coating finish Quenched and tempered Carburized nitriding hardened Black Black oxide finish Black oxide finish Lever Unclamping Mode Clamping Mode S45C steel Chrome plated ★Key Point The handle clicks at clamping end. Clamping Spindle Phenolic plastic Black SCM435 steel Quenched and tempered Black oxide finish Hex-Head Bolt M6×1-20L (Threaded hole depth:12) Recommended Clamping Position Unclamping Position L3 Recommended Clamping Position L Clamp Starting Position

Open the catalog to page 12
Spring Clamps - 13

Part Number Projecting Stroke Clamping Stroke Handle Operating Clamping Weight Load (N) Force (N) (g) How To Set Handle To Recommended Clamping Position Clamping Clamping End Clamping Spindle Half of Clamping Stroke 1. Set the clamping spindle to contact a workpiece at clamping end position. 2. Project the clamping spindle by about half of the clamping stroke and tighten the nut. Note ・The clamping forces and handle operationg loads stated above can vary by up to ± 20%. ・When the reaction force(F) becomes greater than the clamping force, clamping is lifted. ・The long handle facilitates...

Open the catalog to page 13
Spring Clamps - 14

CLAMPING SPINDLES Dedicated for Snap Clamps Urethane plastic Part Number Part Number Proper Snap Clamps Mini Hold-Down Standard Hold-Down Push-Pull Tip Screw Hex. Nut Black urethane plastic SCM435 steel SS400 steel Shore A90 Trivalent chromate plated Trivalent chromate plated Installation example The urethane tip avoids marring soft or finished s

Open the catalog to page 14

All Imao Corporation catalogs and technical brochures

  1. QLCL

    2 Pages

  2. Side Clamps

    27 Pages

  3. Flex Locators

    38 Pages

  4. WORK SUPPORTS

    24 Pages

  5. TENSIONERS

    40 Pages

  6. CLAMPS

    106 Pages

  7. SCREWS & NUTS

    13 Pages

  8. CLAMPING KNOBS

    23 Pages

  9. LOCATING PARTS

    14 Pages

  10. GRIPPERS

    19 Pages