Value Creator

Value Creator

SPRING SWING CLAMPS ★Key Point -[ Handle clicks at the clamping end point. Body

*)Clamping height is adjustable within the listed range. Part Number **) Values at the midpoint of the clamping stroke. It varies within the listed range depending on the contact point ofthe clamping spindle that decides the spring tension. Feature ■Turn the handle after the arm swings into position, the cam shaft rotates along the guide pin to push down the arm. The clamping spindle contacts the workpiece and the cam shaft moves up and compresses the spring to clamp the workpiece. ■ Easy clamping with one touch operation. Handle clicks attheclampingend point. ■Spring-loaded clamp provides constant...

VERTICAL-HANDLE HOLD-DOWN SNAP CLAMPS (Mini) HIMO(Black Oxide Finish) (Stainless Steel) (Electroless Nickel Plated) Type

How To Use Use alBJ6011 Small Cylindrical Risers to raise these clamps. / Note ■The clamping forces and handle operating loads stated above can vary byupto± 20%. ■When the reaction force(F) becomes greater than the clamping force, clamping is lifted. Related Product |UB iCIamping Spindles with a plastic tip are available for clamping without marring a part. I.Set the clamping spindle 2. Project the clamping spindle by to contact a workpiece at about half of the clamping stroke clamping end position. and tighten the nut.

VERTICAL-HANDLE HOLD-DOWN SNAP CLAMPS Unclamping Mode Clamping Mode [ The handle clicks at clamping end.

■The long handle facilitates clamping operation. ■The handle is locked atthe unclamping position ■Uses a snap-on system (double locking) ■|QLSND-EX20| Extension Arms to extend the clamp arm. ■|QLSND-AN10| Angle Adaptors to set the handle in an angled position. ■[UB]Clamping Spindles to protect workpieces from being marred.

Dedicated for Snap Clamps EXTENSION ARMmo Body S45C steel Black oxide finish Part Number Supplied With Clamping Forces Generated in Use of Extension Arms Hex. socket head setscrew M5X0.8-14L X2 pcs.

RettS Part Number Dimensions of Snap Clamps with Angular Adaptor Installed Supplied With Hex.socket head cap screw M6X1-12L X 1pc. Remove the handle and then install an Angular Adaptor between the b°dy and the handle. perfect in applications where the handle can (Use a wrench of nominal size 9 for removal of not be turned to the clamping position.

QLSNS PUSH-PULL SNAP CLAMPSHIMO ★Key Point ->. [ The handle clicks at clamping end. ^

■The long handle facilitates clamping operation. ■The handle is locked atthe unclamping position. ■Uses a snap-on system (double locking) ■IQLSND-AN10I Angle Adaptors to set the handle in an angled position. ■|UBI Clamping Spindles to protect workpieces from being marred.

CLAMPING SPINDLES imno Part Number Part Number

Value Creator

THRUST CLAMPS Light-Duty Heavy-Duty(Marked with Blue Arrow) (Marked with Black Arrow) Body/Lever Arm

&ODPSLQJ 'LUHFWLRQ &ODPSLQJ 'LUHFWLRQ Feature わ 6SULQJORDGHGFODPSWKDWSURYLGHVFRQVWDQWFODPSLQJIRUFH わ/RQJFODPSLQJEDUSURMHFWLRQUDQJHDOORZVFODPSLQJDUHFHVVHGSDUW わ&ODPSLQJ%DUVDUHQRWLQFOXGHG PXVWEHRUGHUHGVHSDUDWHO\ :KHQXVLQJ\RXURZQFODPSLQJEDUHQVXUHWKDWWKHGLDPHWHULVILQLVKHGWRDKRUEHWWHUWROHUDQFH Note :KHQDUHDFWLRQIRUFH ) EHFRPHVJUHDWHUWKDQDFODPSLQJ IRUFHWKHFODPSLQJEDUVOLGHVEDFNWRJHWDSDUWXQFODPSHG

THRUST CLAMPS (Vertical) Light-Duty Heavy-Duty(Marked with Blue Arrow) (Marked with Black Arrow) Note: Clamping bar is not included. QLRCS „ (To be ordered separately) Counterclockwise Clamping CAD Download : https://www.imao.com/en/ imflocoRPORfinon

QLRCF-Ll (Light-Duty) • Operation of CW Type (Invert the operation for CCW type.) Unclamping Position 2. Clamping Setup Project the clamping bar until it contacts the part. 3. Clamping Turn the lever handle (120°) to the clamping ■Application Example (Vertical Clamping)

imflo corporator

Value Creator

PRECISION THRUST CLAMPS Body Part Number *) The minimum clamping force at clamping end position, and the maximum clamping force at clamp starting position.

Feature ・Precision Thrust Clamps can clamp at the same position by precise projection of clamping bars. ・Spring-loaded clamp provides constant clamping force. ・The handle clicks to indicate completed clamping. ■How to Install Attachments ■How to Replace Handle When installing an attachment on the clamping bar, lock the clamping bar using a wrench to prevent it from receiving any torque. The handle is replaceable. When installing/removing a handle, do not apply torque to the Linkage End. Linkage End (M4×0.7) Screw (M4×0.7) Attachment Technical Information ■Allowable Load and Accuracy of Clamping...