Side Clamps
27Pages

Side Clamps

CLAMPING PLATES COMPACT WEDGE CLAMPS COMPACT SIDE CLAMPS COMPACT LOW-PROFILE CAM EDGE CLAMPS LOW-PROFILE CAM EDGE CLAMPS SIDE CLAMPS

SIDE CLAMPS SIDE CLAMPS SIDE CLAMPS SIDE CLAMPS WIDE-JAW SIDE CLAMPS

SPIRAL CAM CLAMPS ★Key Point Space saving. Long clamping stroke. Spiral Cam Clamp Clamping Plate SCM440 steel SUS304CSP Black oxide finished stainless steel HRC33-39 Clamping Plate With Clamping Plate Without Clamping Plate Part Number Allowable Screw Torque (Nm) With Clamping Plate Part Number Clamping Plate Without Clamping Plate Part Number SPIRAL CAM CLAMPS One-To

Feature ・ The spiral cam provides quick and powerful clamping. ・ The simple design keeps cost low and the small size allows more workpieces per load. ・ Clamping Plate avoids marring workpiece surfaces. ■Mounting Hole Dimension With Clamping Plate Without Clamping Plate Mounting Hole M More than C1.5 Mounting Hole M More than C1.5 Part Number Note: Dimension A and A+1 are the recommended distances between the mounting hole and the end of the workpiece. ・Tighten clockwise to clamp the workpiece. ・Mount a stop on the right side of the workpiece. Stop Tighten Spiral Cam Clamp fully and loosen...

COMPACT WEDGE CLAMPS W3 Part Number Clamping Force Allowable Screw Torque (kN) (N・m) ・The wedge construction allows powerfully clamping the workpiece. ・Can hold two workpieces with equilateral clamping action by using a hex wrench. Jaws move obliquely downward ① ② SCM435 steel Black oxide finished Fluoro rubber Proper O-ring SNCM439 steel Black oxide finished HRC33-39 Can clamp 2 workpieces in small space. ★Key Point Part Number M-Hex. Socket-Head Cap Screw M-Countersunk Head Screw ①Horizontal pressure against workpiece ②Vertical pressure preventing workpiece lift Compact design allows to...

COMPACT SIDE CLAMPS L M-For Socket-Head Cap Screw Cross Section SCM440 steel Black oxide finished HRC33-39 Fluoro rubber Part Number Clamping Force Allowable Screw Torque Weight (kN) (N・m) (g) Part Number Proper O-ring Feature Jaw moves obliquely downward ① ② ①Horizontal pressure against workpiece ②Vertical pressure preventing workpiece lift ■Mounting-Hole Dimension Drill a tapped hole and a locking-pin hole as specified below Part Number

COMPACT LOW-PROFILE CAM EDGE CLAMPS S45C steel Black oxide finished SCM440 steel Black oxide finished HRC39-45 Part Number Allowable Screw Torque Clamping Force (N・m) (kN)

Feature Designed to prevent part lift. How To Use ・ Low head cap screws do not project from the body. ・ Turning the cam with a hex wrench allows the cam to project the jaw for clamping. When the cam is turned back for unclamping, the loaded spring lets the jaw return to the original position. ■Mounting-Hole Dimension Note Ensure that mounting surfaces are finished to 6.3 (6.3a) or better, without any scratches or dents.

LOW-PROFILE CAM EDGE CLAMPS S45C steel Black oxide finish SCM440 steel Quenched and tempered Black oxide finish W3 (Across 2 Flats of Hex Hole) Part Number Allowable Screw Torque Clamping Force Weight (N・m) (kN) (g) Clamping Mechanism

Feature Designed to prevent part lift. Hex-Socket Head Cap Screw Turning the wrench allows the cam to project the jaw for clamping. When the wrench is turned back for unclamping, the loaded spring lets the jaw return to the original position. Clamping Force(kN) Operating Load(N・m) Note Ensure that mounting surfaces are finished to (6.3a) or better, without any scratches or dents. LOW-PROFILE CAM EDGE CLAMPS One-Touch type is available.

COMPACT TOE CLAMPS M-For Socket-Head Cap Screw Cross Section SCM440 steel Black oxide finished HRC33-39 Fluoro rubber Part Number Part Number Clamping Force Allowable Screw Torque Weight (kN) (N・m) (g) Proper O-ring （Jaw moves obliquely downward） ① ② ①Horizontal pressure against workpiece ②Vertical pressure preventing workpiece lift ■Mounting-Hole Dimension Drill a tapped hole and a locking-pin hole as specified below． Part Number

M- Hex. Socket Head Cap Screws S45C steel Quenched and tempered Black oxide finish Part Number Clamping Allowable Screw Weight Force(kN) Torque(N・m) (g) ■Mounting-Hole Dimension Locking Pin Drill a tapped hole and a pin hole as specified on the above Supplied With One flat washer

Sliding Nose SCM440 steel Induction hardened SCM440 steel (clamping face) Quenched and tempered Black oxide finish Black oxide finish Precision ground (smooth nose) Serrated Nose Smooth Nose M-For Hex. Socket Head Cap Screws Serrated Nose Smooth Nose Smooth Serrated Nose Part Number Related Product BJ101-02 Clamping Screws Clamping Allowable Screw Weight Force(kN) Torque(N・m) (g)

Cam / Locking Screw Flanged Collar SCM435 steel SK95 steel Quenched and tempered Quenched and tempered Black oxide finish Black oxide finish Part Number Allowable Screw Torque Clamping Force (N・m) (kN) Part Number Feature ・Allows loading and unloading a part faster. ・Compact design How To Use To install， lock the flanged collar into the cam using the locking screw and then tighten up the cam with a wrench． Locking Screw Flanged Collar Cam Parts Breakdown Provides positive clamping

SCM435 steel SCM440 steel Quenched and tempered Quenched and tempered Black oxide Black oxide M-Socket Head Cap Screw Part Number Part Number Clamping Force Allowable Screw Torque Weight (kN) (N・m) (g) Socket Head Cap Screw Socket Head Cap Screw Flanged Collar Flanged Collar Cam How To Use Secure the body and the flanged collar with a socket head cap screw, and then turn the the cam with a wrench to clamp a workpiece. Related Product One-Touch type is available. QLSC CAM EDGE CLAMPS

SIDE CLAMPS M- Hex. Socket Head Cap Screws S45C steel Quenched and tempered Black oxide finish Clamping Allowable Screw Weight Force(kN) Torque(N・m) (g) ■Mounting-Hole Dimension Locking Pin Drill a tapped hole and a pin hole as specified on the above Supplied With One flat washer

SIDE CLAMPS Body/Sliding Nose SCM440 steel Quenched and tempered Black oxide finish SCM440 steel Quenched and tempered Black oxide finish Precision ground (smooth nose) Serrated Nose Smooth Nose M-For Hex. Socket Head Cap Screws Nose Part Number Smooth Serrated Related Product BJ101-02 Clamping Screws Clamping Allowable Screw Weight Force(kN) Torque(N・m) (g)