MT9J003
77Pages

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Features 1/2.3-Inch 10 Mp CMOS Digital Image Sensor MT9J003 Datasheet, Rev. E For the latest datasheet, please visit www.onsemi.com Features • 1080p digital video mode • Simple two-wire serial interface • Auto black level calibration • Support for external mechanical shutter • Support for external LED or xenon flash • High frame rate preview mode with arbitrary downsize scaling from maximum resolution • Programmable controls: gain, horizontal and vertical blanking, auto black level offset correction, frame size/rate, exposure, left-right and top-bottom image reversal, window size, and panning • Data interfaces: parallel or four-lane serial high-speed pixel interface (HiSPi) differential signaling (sub-LVDS) • On-die phase-locked loop (PLL) oscillator • Bayer pattern downsize scaler • Integrated position-based color and lens shading correction • One-time programmable memory (OTPM) for storing module information Applications • Digital video cameras • Digital still cameras General Description The ON Semiconductor MT9J003 is a 1/2.3-inch CMOS active-pixel digital imaging sensor with an active pixel array of 3856H x 2764V including border pixels. It can support 10 megapixel (3664H x 2748V) digital still images and a 1080p (3840H x 2160V) digital video mode. It incorporates sophisticated on-chip camera functions such as windowing, mirroring, column and row skip modes, and snapshot mode. It is programmable through a simple two-wire serial interface and has very low power consumption. Table 1: Key Performance Parameters

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Ordering Information Table 2: Available Part Numbers

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Table of Contents Table of Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor List of Figures List of Figures Figure 1: Figure 2: Figure 3: Figure 4: Figure 5: Figure 6: Figure 7: Figure 8: Figure 9: Figure 10: Figure 11: Figure 12: Figure 13: Figure 14: Figure 15: Figure 16: Figure 17: Figure 18: Figure 19: Figure 20: Figure 21: Figure 22: Figure 23: Figure 24: Figure 25: Figure 26: Figure 27: Figure 28: Figure 29: Figure 30: Figure 31: Figure 32: Figure 33: Figure 34: Figure 35: Figure 36: Figure 37: Figure 38: Figure 39: Figure 40: Figure 41: Figure 42: Figure 43: Figure 44: Figure 45: Figure 46: Figure 47:...

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor List of Tables List of Tables Table 1: Table 2: Table 3: Table 4: Table 5: Table 6: Table 7: Table 8: Table 9: Table 10: Table 11: Table 12: Table 13: Table 14: Table 15: Table 16: Table 17: Table 18: Table 19: Table 20: Table 21: Table 22: Table 23: Table 24: Table 25: Table 26: Table 27: Table 28: Table 29: Table 30: Table 31: Table 32: Table 33: Table 34: Table 35: Table 36: Table 37: Table 38: Key Performance Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor General Description General Description The MT9J003 digital image sensor features ON Semiconductor’s breakthrough low-noise CMOS imaging technology that achieves near-CCD image quality (based on signal-tonoise ratio and low-light sensitivity) while maintaining the inherent size, cost, and integration advantages of CMOS. When operated in its default 4:3 still-mode, the sensor generates a full resolution image at 15 frames per second (fps) using the HiSPi serial interface. An on-chip analog-todigital converter (ADC) generates a 12-bit value...

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Functional Overview The output from the sensor is a Bayer pattern; alternate rows are a sequence of either green and red pixels or blue and green pixels. The offset and gain stages of the analog signal chain provide per-color control of the pixel data. The control registers, timing and control, and digital processing functions shown in Figure 1 on page 6 are partitioned into three logical parts: • A sensor core that provides array control and data path corrections. The output of the sensor core is a 12-bit parallel pixel data stream...

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Operating Modes Operating Modes By default, the MT9J003 powers up with the serial pixel data interface enabled. The sensor can operate in serial HiSPi or parallel mode. For low-noise operation, the MT9J003 requires separate power supplies for analog and digital power. Incoming digital and analog ground conductors should be placed in such a way that coupling between the two are minimized. Both power supply rails should also be routed in such a way that noise coupling between the two supplies and ground is minimized. Caution ON Semiconductor...

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Operating Modes 5. VPP, which can be used during the module manufacturing process, is not shown in Figure 3. This pad is left unconnected during normal operation. 6. The parallel interface output pads can be left unconnected if the serial output interface is used. 7. ON Semiconductor recommends that 0.1F and 10F decoupling capacitors for each power supply are mounted as close as possible to the pad. Actual values and results may vary depending on layout and design considerations. Check the MT9J003 demo headboard schematics for circuit...

MT9J003: 1/2.3-Inch 10 Mp CMOS Digital Image Sensor Operating ModesFigure 4: Typical Configuration: Parallel Pixel Data Interface PLL Analog Analog power1 power1 power1 From Controller Analog ground Digital ground 1. All power supplies should be adequately decoupled. 2. ON Semiconductor recommends a resistor value of 1.5kQ, but it may be greater for slower two-wire speed. 3. This pull-up resistor is not required if the controller drives a valid logic level on SCLK at all times. 4. The GPI pins can be statically pulled HIGH or LOW to be used as module IDs, or they can be programmed to...