DMX Modular Progressive Divider Valves Catalogue
26Pages

DMX/DMX-A Modular progressive divider valves High quality and high tolerance with precision machines

DMX Description Technical data Assembly and components Bases Metering bases Ordering codes (Zi-Ni) Single bases Assembly Single bases Assembly Ordering codes (SS316L Steel) Junctions BANJO with grease nipple Inset filter Inset filter 70 p Valvole Shut-Off EV-2 Shut-Off Valves Inductive control (ATEX) 15 Pressure pin indicator (with memory) 17 Bridge element and sensors 17 PUSH-IN Fittings Straight 18 Metering block assembly order 19 Assembly ordering codes 19 Metering valves Metering valves components 1 With visual pin indicator 1 With inductive sensor M8 1 With...

Features and general description DMX is a progressive modular distributor. It measures out and divides lubricant thanks to piston movement. This system is highly qualified to measure out oil and grease for one or more support groups. Every piston is in line with the previous one and the next one. When a piston fails to work, as for an external obstruction, the whole system stops (this happens even when we place a plug on a unused outlet). The DMX modular system consists of two main parts: Base (divided into initial base, intermediate base and final base) and the Metering Elements (available...

Technical data Parts protective coating Zinc-Nickel 800 hour salt spray tested Steel, Zn-Ni plated (free of Cr-V) or SS316L Metering element Supplied with screw Element: initial base Supplied with screw and "O"-Ring Element: intermediate base Supplied with screw, adapter screw and "O"-Ring Element: final base Supllied with screw Metering valves interchangeability Graco MSP - Bijur serie M2500G - Dropsa serie SMX Bridge element Supplied with adapter screw. Screw replace junctions bridge in order to convey the ouput of one or more output into the next one. By-pass element Monitoring element...

Metering bases The metering base is made of a serie of at least three elements: one initial base, an intermediate one and a final one. Thanks to a flexible and easy assembling process, the intermediate bases can be increased later to a maximum of 18. We can always add modules using the fixing bushes supplied with the assembly. The system can operate ad high pressures without lubricant loss between elements. Intermediate base Initial base Fixing bushes Final base Base assembling screw I.L.C. srl - Via Garibaldi, 149 - 20155 Gorla Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 -...

BASES Single bases I.L.C. srl - Via Garibaldi, 149 - 20155 Goria Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 - www.iiciube.com - info@ilclube.it

Ordering codes (SS316L Steel) Single bases I.L.C. srl - Via Garibaldi, 149 - 20155 Goria Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 - www.ilclube.com - info@ilclube.it

BASES BANJO with grease nipple 03.355.5/ 03.355.7 Inset filter Banjo junctions are placed on a progressive distributor inset. Their job is to let us use a manual or hidrau-lic pump when the main pump does not work. Code Thread These strainer prevent the lubricant lines from being obstructed by impurities. Supply joints included. Filtration rate 150 p Plug 1/4" BSP (F) Codice Grado di filtrazione 07.270.5 These strainer prevent the lurbricant lines from being obstructed by impurities. Filtration rate 70 p Plug 1/4" BSP (F) I.L.C. srl - Via Garibaldi, 149 - 20155 Gorla Minore - Italy...

Shut-Off Valves Valvole Shut-Off EV-2 SHUT OFF valves EV-2 are made of a special "NC" 2-ways solenoid valve and of a modular base that can be directly assembled on the DPL inlet. EV-2 valve is the essential element in order to transforma a standard progressive system into a sectioned system. Technical data Olii viscosita min 32 cSt) Grasso max NLGI-1 I.L.C. srl - Via Garibaldi, 149 - 20155 Goria Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 - www.ilclube.com - info@ilclube.it

METERING VALVES Metering valves components The minimum number of metering valves in an assembled block is 3 and the maximum is 20. toring control sensor, are mandatory in order to choose the right model. The installation on the base is made using the two fixing screws TEC-UNI-5931 UNF 1/4 “x 1” 1/4 supplied with the metering valve. It ‘s always possible to replace a valve with a different model without disconnecting the tubelines or open the base. The number of required metering elements, as long as their output and the presence of a moni- Assembling dosing elements is extremely simple....

METERING VALVES Outlets BE CAREFUL! Always shut a no-longer-required outlet as shown in the image below. Else you would occur in system block and a valve alarm. Metering elements are supplied with a set-up for one or two separate outputs. It is always possible to modify this condition (from one to two and viceversa) turning the adapter screw between the vertical outputs as explained in the image below. It is possible to sum the two output of the same element. Remove the grub screw (code A51.087096 1/8" K) and the ring (Code A53.114116) replacing it with the grub screw (code A92.087058 1/8"...

Ordering codes Zi-Ni METERING VALVES double outlet Metering Valve single outlet With visual pin indicator double outlet single outlet With inductive sensor M8 double outlet single outlet With inductive sensor M12 double outlet single outlet I.L.C. srl - Via Garibaldi, 149 - 20155 Goria Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 - www.ilclube.com - info@ilclube.it

METERING VALVES double outlet Metering Valve single outlet With visual pin indicator double outlet single outlet With inductive sensor M8 double outlet single outlet With inductive sensor M12 double outlet single outlet I.L.C. srl - Via Garibaldi, 149 - 20155 Goria Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 - www.ilclube.com - info@ilclube.it

Cycle control METERING VALVESVisual pin Inductive control The visual pin shows the piston movement, monitoring the proper operation of the entire system. In this control a proximity switch is housed in a composite block. The piston opens and closes the contact as it moves into its operational seat. They are usually used in cycle control systems where they can count up to 300 movement for minute. Electrical Data I.L.C. srl - Via Garibaldi, 149 - 20155 Goria Minore - Italy Phone +39 0331 601697 - Fax +39 0331 602001 - www.ilclube.com - info@ilclube.it