WM-44 SS V3.
3Pages

{{requestButtons}}

Catalog excerpts

WM-44 SS V3. - 1

Anemometer display unit for panels with alarms for cranes. Installation Panel KHH WM 44-$$ Small panel display unit and wind speed sensor with pre-alarm and alarm. With 20 mm digits (0.8" display unit). Ideal in conjunction with the Anemo4403 sensor. Adaptable to a wide range of anemometer sensors. Pre-alarm (ALARM1) and Alarm (ALARM2).Designed for mounting on a 72 x 36 panel, such as in electrical cabinets. Especially designed for construction cranes. For installation on DIN RAIL see model WM44-DRM. Display Wind data displayed with two 20 mm digits. 2 alarm indicator LEDs enabled “AL1 and AL2”. Wind speed in km/h and mph. Programming in kilometres/hour ( km/h) or in miles/hour (mph). P01 You can switch between km/h and mph at any time by pressing “Select", a user accessible button. The alarm is triggered when the programmed value is reached or surpassed and it has includes a delay to prevent false alarms due to short gusts. The alarm is disabled when the wind speed drops below the programmed value and provided this condition persists for a minimum period. When ALARM 2 is enabled ALARM 1 is disabled. When ALARM 2 is enabled, the reading on the display will blink, as a warning. Alarms can be programmed for the following: trigger values, intermittent or continuous, interlocked (only alarm2). The alarm outputs are through voltage-free relay contacts. Choice between: on contact open or on contact close. Possibility of alarm interlock 2. With the alarm disabled when the unit's power supply is cut off. Anemometer sensors Suitable for a wide range of sensors: Power supply sensors: 20 V or 10 VDC, from the unit itself, types: 3-wire and 2-wire (see examples on faceplate connections from the unit itself). We RECOMMEND pairing the unit with our Anemo4403 model. Preset user program configuration In addition to user-programmed another, alternative programming can be saved in memory. This can be retrieved any time by going to the program step. POO option 4.

Open the catalog to page 1
WM-44 SS V3. - 2

Para acceder a los pulsadores de programacion, levantar la caratula frontal haciendo palanca en la abertura inferior, donde indica “open to program”. Para entrar en programacion, pulsar simultaneamente los pulsadores UP y Scape durante 2 segundos. Button functions in programming mode UP Moves up program steps (POO, P01..), options or values to be programmed. DOWN Moves down program steps, options or values ENTER Enters the program step currently displayed, validates options and values and exits program step. Returns to program steps. Selects the digit to be modified within the range....

Open the catalog to page 2
WM-44 SS V3. - 3

32m Namur type sensors have the same connection as the ONIX Anemo4403 sensor. The power supply for the sensors should come exclusively from the WM44-SS unit. The inputs are not insulated. It does not admit direct external signals. The size of the space on the panel where the unit is to be installed should be 67X32,5mm. The size of the space on the panel where the unit is to be installed should be 67x32.5 mm

Open the catalog to page 3

All IED COMPANY catalogs and technical brochures

  1. WIND VANE

    6 Pages

  2. ANEMO5H25 V3

    2 Pages

  3. VT

    2 Pages

  4. AI-2

    2 Pages

  5. SRR4

    2 Pages

  6. SRR4 868

    2 Pages

  7. WM44-SS_EN

    2 Pages

  8. WM44_EN

    2 Pages

  9. WM44-P_RF_EN

    2 Pages

  10. SAG-105WR_EN

    2 Pages

  11. WM44-EVO_EN

    2 Pages