Safety Overview XW Series E-Stops Interlock Switches Enabling Switches Safety Control Light Curtains AS-Interface Safety at Work

AS-Interface Safety at Work AS-Interface Safety at Work AS-Interface safety at work integrates a safety network into one wire-saving system. • Emergency stop switches can be connected directly to AS-Interface Safety at Work, further reducing wiring. • Interlock switches, safety relay modules and other safety components can be connected to the safety network via safety slaves. • Safety components can be connected to other networks through gateways. • Safety slaves and safety monitors can be simply connected to the existing AS-Interface network to establish the AS-Interface Safety at Work. Interlock...

AS-Interface Safety at Work MicroSmart Series AS-Interface Master Module + FC4A FC5A Interlock Switches Non-contact Interlock Switch Gateway SX5A AS-Interface Safety / Gateway Enabling Switches Safety Control Control Unit SX5A AS-Interface Safety Monitor PS2R AS-Interface Power Supplies Light Curtains Safety slaves and standard slaves can be connected to one network. AS-Interface Safety at Work Photoelectric Switches

AS-Interface Safety at Work Emergency Stop Switches Emergency Stop Switches XA Series/XW Series/FB Series (Plastic Enclosures) with Safety Slave Functions for Direct Connection to the AS-Interface Safety at Work Interlock Switches • Emergency stop switches with safety slave functions can be connected to the AS-Interface Safety at Work network. • Complies with IEC 61508 SIL3 (Functional safety of electrical/electronic/programmable electronic safety-related systems) and EN954-1 safety category 4 (Safety of machinery-Safety related parts of control systems). • Space, wire, and labor-saving solutions...

AS-Interface Safety at Work Emergency Stop Switches Accessories Part Number XA/XW Series IDC Connector Kit 1 Through connector (with cover) IDC Connector Termination Tool Length 500 mm, with one connector Length 1m, with one connector Crimping Type Connector Cable FB Series Control Station M12 Connector Cable Hand-held Programming Device Specication End connector (with cover) Interlock Switches 1. Minimum order is 5 pieces. IDC connector termination tool MMIT-156F (ITW Pancon) may be required to connect the cable to the connector. 2. *Hand-held programming device accessories: -Programming device...

AS-Interface Safety at Work Emergency Stop Switches Minimum Operator Stroke Required for Direct Opening Action Maximum Operating Stroke Operating Frequency Mechanical Life Electrical Life IDC connector (XA series) IDC connector, crimping connector (XW series) M12 connector/AS-Interface piercing connector (FB series) Recommended Tightening Torque for Locking Ring Interlock Switches Pushlock: 10.5N (XA series), 32N (XW, FB series) Pull reset: 10N (XA series), 21N (XW, FB series) Turn reset: 0.16N·m (XA series), 0.27 N·m (XW, FB series) Minimum Force Required for Direct Opening Action Operating...

AS-Interface Safety at Work Emergency Stop Switches Panel Cut-out Communication Block Communication Block Panel Cut-out M12 Connector Cable for FB Series L 4-M4 Tapping Screw Holes for Rear Mounting (Depth: 10 mm) 2-Front Mounting Holes ø14 Knockout Interlock Switches AS-Interface Cable Piercing Model ∗Without nameplate: 32 With nameplate: 33.5 Enabling Switches 4-M4 Tapping Screw Holes for Rear Mounting (Depth: 10 mm) 2-Front Mounting Holes ø14 Knockout ∗Without nameplate: 32 With nameplate: 33.5 These emergency stop switches are push-lock, pull/turn reset types. When pressed, the operator is...

Operating Instructions AS-Interface Safety at Work Operating Instructions AS-Interface Safety Monitor Emergency Stop Switches Panel Mounting Before wiring the interface cable, discharge static electricity. Tighten the screws to a torque of 0.8 to 1.2 N·m. The AS-Interface power supply unit must separate the main power (input) and output safely according to IEC 60742. It must also maintain a stable supply in the event of instantaneous power failure. Replacing the Safety Slave Press “Service” button before and after replacing the safety slave. Resetting of safety monitor using the PC is not necessary....